Cutting Machine Silhouette Curio 2 - Versionshistorik

Arru den 11 juni 2026 kl. 08.51

2026-06-11T08:51:49Z

← Äldre version		Versionen från 11 juni 2026 kl. 08.51
Rad 43:		Rad 43:
	\|Sticker paper		\|Sticker paper
	\|AutoBlade or Kraft blade (see instructions below)		\|AutoBlade or Kraft blade (see instructions below)
	\|Cameo mat		\|Debris tray with taped-on Cameo mat
	\|-		\|-
	\|Shape-cut card		\|Shape-cut card

Arru: /* Setups & settings */

2026-06-11T08:51:26Z

Setups & settings

← Äldre version		Versionen från 11 juni 2026 kl. 08.51
Rad 39:		Rad 39:
	\|Fixed or AutoBlade		\|Fixed or AutoBlade
	\|Debris tray with taped-on Cameo mat		\|Debris tray with taped-on Cameo mat
			\|-
			\|Printed stickers
			\|Sticker paper
			\|AutoBlade or Kraft blade (see instructions below)
			\|Cameo mat
	\|-		\|-
	\|Shape-cut card		\|Shape-cut card
	\|Card stock		\|Card stock
	\|~~Craft~~ blade (orange)		\|Kraft blade (orange)
	\|Debris tray with taped-on Cameo mat		\|Debris tray with taped-on Cameo mat
	\|-		\|-

Arru: /* Cutting prints with registration marks */

2026-06-11T08:47:29Z

Cutting prints with registration marks

← Äldre version		Versionen från 11 juni 2026 kl. 08.47
Rad 138:		Rad 138:

	=== Cutting prints with registration marks ===		=== Cutting prints with registration marks ===
	Using this technique and suitable sticker paper you can make professional-looking cut-out stickers. There are also other uses, like business- or playing cards, signs etc.		Using this technique and suitable sticker paper you can make professional-looking cut-out stickers by perfectly matching cut-outs with a printed design. There are also other uses, like business- or playing cards, signs etc.

	This is a feature of the Curio 2 cutter, so it cannot be done on Cameo Pro.		This is a feature of the Curio 2 cutter, so it cannot be done on Cameo Pro.

Arru: /* Cutting instructions */ cutting with registration marks

2026-06-11T08:44:11Z

Cutting instructions: cutting with registration marks

@@ Rad 136: / Rad 136: @@
 *# Find the cut job listed next to the Send button in Silhouette studio. Press close ╳ next to the cut job.
 * To resume, press ⏸️ button again
 == Heat foil instructions ==

Arru: /* Pausing/emergency stop */

2025-12-27T13:16:09Z

Pausing/emergency stop

← Äldre version		Versionen från 27 december 2025 kl. 13.16
Rad 133:		Rad 133:
	* Press the ⏸️ button in the control panel (only lit while cutting)		* Press the ⏸️ button in the control panel (only lit while cutting)
	* To cancel cutting completely:		* To cancel cutting completely:
	*# Long press the ⏸️ button again for ≈ 10 seconds		*# Long press the ⏸️ button again for ≈ 10 seconds, the sled will return to the rear left starting position
	*# Find the cut job listed next to the Send button in Silhouette studio. Press close ╳ next to the cut job.		*# Find the cut job listed next to the Send button in Silhouette studio. Press close ╳ next to the cut job.
	* To resume, press ⏸️ button again		* To resume, press ⏸️ button again

Arru: /* Pausing/emergency stop */

2025-12-27T13:15:29Z

Pausing/emergency stop

← Äldre version		Versionen från 27 december 2025 kl. 13.15
Rad 133:		Rad 133:
	* Press the ⏸️ button in the control panel (only lit while cutting)		* Press the ⏸️ button in the control panel (only lit while cutting)
	* To cancel cutting completely:		* To cancel cutting completely:
	*# Long press the ~~pause~~ button again for ≈ 10 seconds		*# Long press the ⏸️ button again for ≈ 10 seconds
	*# Find the cut job listed next to the Send button in Silhouette studio. Press close ╳ next to the cut job.		*# Find the cut job listed next to the Send button in Silhouette studio. Press close ╳ next to the cut job.
	* To resume, press ⏸️ button again		* To resume, press ⏸️ button again

Arru: /* Mounting foil */

2025-12-27T12:05:50Z

Mounting foil

← Äldre version		Versionen från 27 december 2025 kl. 12.05
Rad 203:		Rad 203:
	# wipe the acrylic surface with isopropyl alcohol so that it is squeaky clean		# wipe the acrylic surface with isopropyl alcohol so that it is squeaky clean
	# measure a suitable length of heat transfer foil to cover the areas with the design. Make room on the sides of the actual design for attaching tape, foil transfer does not work well with tape on top		# measure a suitable length of heat transfer foil to cover the areas with the design. Make room on the sides of the actual design for attaching tape, foil transfer does not work well with tape on top
	# find best pair of scissors on hand – the foil is very delicate		# find the best pair of scissors on hand – the foil is very delicate
	# cut the foil to length		# cut the foil to length
	# roll foil onto piece + jig, use squegee (among the cutter tools on the wall) to wipe the foil all flush against the surface		# roll foil onto piece + jig, use squegee (among the cutter tools on the wall) to wipe the foil all flush against the surface
	# apply masking tape at the edges, gently pulling to get the foil flat ~~agains~~ the surface		# apply masking tape at the edges, gently pulling to get the foil flat against the surface

	=== Foil transfer ===		=== Foil transfer ===

Arru: /* Mounting foil */ foil preparation

2025-12-27T12:04:47Z

Mounting foil: foil preparation

← Äldre version		Versionen från 27 december 2025 kl. 12.04
Rad 203:		Rad 203:
	# wipe the acrylic surface with isopropyl alcohol so that it is squeaky clean		# wipe the acrylic surface with isopropyl alcohol so that it is squeaky clean
	# measure a suitable length of heat transfer foil to cover the areas with the design. Make room on the sides of the actual design for attaching tape, foil transfer does not work well with tape on top		# measure a suitable length of heat transfer foil to cover the areas with the design. Make room on the sides of the actual design for attaching tape, foil transfer does not work well with tape on top
	# ~~cut it using the~~ best pair of scissors ~~you can find as~~ the foil is very delicate		# find best pair of scissors on hand – the foil is very delicate
	# roll foil onto piece + jig, use squegee (~~part of~~ the cutter tools on the wall) to wipe the foil all flush against the surface		# cut the foil to length
			# roll foil onto piece + jig, use squegee (among the cutter tools on the wall) to wipe the foil all flush against the surface
	# apply masking tape at the edges, gently pulling to get the foil flat agains the surface		# apply masking tape at the edges, gently pulling to get the foil flat agains the surface

Arru: /* Mounting foil */

2025-12-27T12:01:25Z

Mounting foil

← Äldre version		Versionen från 27 december 2025 kl. 12.01
Rad 202:		Rad 202:

	# wipe the acrylic surface with isopropyl alcohol so that it is squeaky clean		# wipe the acrylic surface with isopropyl alcohol so that it is squeaky clean
	# measure a suitable length of heat transfer foil to cover the areas with the design		# measure a suitable length of heat transfer foil to cover the areas with the design. Make room on the sides of the actual design for attaching tape, foil transfer does not work well with tape on top
	# cut it using the best pair of scissors you can find as the foil is very delicate		# cut it using the best pair of scissors you can find as the foil is very delicate
	# roll foil onto piece + jig, use squegee (part of the cutter tools on the wall) to wipe the foil all flush against the surface		# roll foil onto piece + jig, use squegee (part of the cutter tools on the wall) to wipe the foil all flush against the surface

Arru: /* Material set-up */

2025-12-27T11:57:38Z

Material set-up

← Äldre version		Versionen från 27 december 2025 kl. 11.57
Rad 199:		Rad 199:
	## Choose special tools, heat pen fill, and enable the fill style of your choice		## Choose special tools, heat pen fill, and enable the fill style of your choice
	## For a 100% fill, use hatch (lines) fill style with setting from the table		## For a 100% fill, use hatch (lines) fill style with setting from the table
	=== ~~Material set-up~~ ===		=== Mounting foil ===

	# wipe the acrylic surface with isopropyl alcohol so that it is squeaky clean		# wipe the acrylic surface with isopropyl alcohol so that it is squeaky clean
Rad 207:		Rad 207:
	# apply masking tape at the edges, gently pulling to get the foil flat agains the surface		# apply masking tape at the edges, gently pulling to get the foil flat agains the surface

	=== Foil ~~application~~ ===		=== Foil transfer ===

	# Double check that the pen has finished heating up (thermometer on button is all red, not animating)		# Double check that the pen has finished heating up (thermometer on button is all red, not animating)