Plan- och rikthyvel, Scheppach HMC 3200 - Versionshistorik

Elisabeth69: just wording errors

2026-01-20T21:00:31Z

just wording errors

← Äldre version		Versionen från 20 januari 2026 kl. 21.00
Rad 16:		Rad 16:
	\|-		\|-

	\|}~~<br />~~		\|}

	==Generell information==		==Generell information==
	'''<big>The use of pallet wood, reclaimed flooring, reclaimed outdoor deck planks and any kind of wood used for concrete formwork is totally forbidden.</big>'''		'''<big>The use of pallet wood, reclaimed flooring, reclaimed outdoor deck planks and any kind of wood used for concrete formwork is totally forbidden.</big>'''
Rad 72:		Rad 71:

	===Material===		===Material===
	Endast för trä! Only for wood! ~~Do to~~ use wet or green wood. Wait 24 hours before planing glued wood pieces or pieces with epoxy.		Endast för trä! Only for wood! Don't use wet or green wood. Wait 24 hours before planing glued wood pieces or pieces with epoxy.

	Use only clean (without nails, screws or sand particles) wood. No other material allowed.		Use only clean (without nails, screws or sand particles) wood. No other material allowed.

Dan P: /* Logg */

2025-01-05T13:03:07Z

Logg

← Äldre version		Versionen från 5 januari 2025 kl. 13.03
Rad 107:		Rad 107:
	==Logg==		==Logg==

	*2025-01-05: rotated cutting steels on cutterhead (counter clockwise). Some were already rotated, they were left as is in order to get consistency in the orientation of the marker (unrotated marked with permanent marker. (Test runs gave good results.)		*2025-01-05: rotated cutting steels on cutterhead (counter clockwise). Some were already rotated, they were left as is in order to get consistency in the orientation of the marker (unrotated marked with permanent marker. (Test runs gave good results.) Images of markings: [[Media:Planer-IMG20250105130022.jpg]] [[Media:Planer-IMG20250105130039.jpg]] [[Media:Planer-IMG20250105130048.jpg]] [[Media:Planer-IMG20250105130059.jpg]] [[Media:Planer-IMG20250105130116.jpg]]
	*2025-01-02: aluminium gears dead. New ones (including drive chains) ordered.		*2025-01-02: aluminium gears dead. New ones (including drive chains) ordered.
	*2022-02-16: installed the new spiral cutterhead with new bearings.		*2022-02-16: installed the new spiral cutterhead with new bearings.

Dan P: /* Logg */

2025-01-05T12:49:31Z

Logg

← Äldre version		Versionen från 5 januari 2025 kl. 12.49
Rad 107:		Rad 107:
	==Logg==		==Logg==

			*2025-01-05: rotated cutting steels on cutterhead (counter clockwise). Some were already rotated, they were left as is in order to get consistency in the orientation of the marker (unrotated marked with permanent marker. (Test runs gave good results.)
	*2025-01-02: aluminium gears dead. New ones (including drive chains) ordered.		*2025-01-02: aluminium gears dead. New ones (including drive chains) ordered.
	*2022-02-16: installed the new spiral cutterhead with new bearings.		*2022-02-16: installed the new spiral cutterhead with new bearings.

Voxel: /* Spiral cutterhead */

2025-01-04T18:50:29Z

Spiral cutterhead

← Äldre version		Versionen från 4 januari 2025 kl. 18.50
Rad 80:		Rad 80:
	The new spiral cutterhead uses 15mmx15mmx2.5mm-R150 carbide inserts. We have a set of 10 spare.		The new spiral cutterhead uses 15mmx15mmx2.5mm-R150 carbide inserts. We have a set of 10 spare.

	The inserts can be rotated 3 times before being replaced. The recommended torque range is 5.4-5.9 Nm (48-52 pound inch).		The inserts can be rotated 3 times before being replaced. The recommended torque range is 5.4-5.9 Nm (48-52 pound inch).

	~~<s>We currently have 3 sets of blades. Label and store the dull blades. When two sets are dull, send them to resharpening.</s>~~

	==Underhåll och reservdelar==		==Underhåll och reservdelar==

Voxel: /* Logg */

2025-01-04T18:46:56Z

Logg

← Äldre version		Versionen från 4 januari 2025 kl. 18.46
Rad 109:		Rad 109:
	==Logg==		==Logg==

			*2025-01-02: aluminium gears dead. New ones (including drive chains) ordered.
	*2022-02-16: installed the new spiral cutterhead with new bearings.		*2022-02-16: installed the new spiral cutterhead with new bearings.
	*2021-06-01: replaced two needle bearings on the plastic gear in the autofeed mechanism.		*2021-06-01: replaced two needle bearings on the plastic gear in the autofeed mechanism.

Henningk den 9 maj 2024 kl. 09.39

2024-05-09T09:39:27Z

← Äldre version		Versionen från 9 maj 2024 kl. 09.39
Rad 99:		Rad 99:

	===Reservdelar===		===Reservdelar===
	Small yellow belt for the feed mechanism. One spare.		Small yellow belt for the feed mechanism. One spare.

			Replacement belts are available at Clas Ohlson, here is a link https://www.clasohlson.com/se/Plattrem-Scheppach-8-x-340-mm/p/50-2631

	1012 needle bearings for the feed mechanism. 2 spare.		1012 needle bearings for the feed mechanism. 2 spare.

4444: /* Handhavande av maskinen */

2023-11-06T20:17:18Z

Handhavande av maskinen

← Äldre version		Versionen från 6 november 2023 kl. 20.17
Rad 75:		Rad 75:

	Use only clean (without nails, screws or sand particles) wood. No other material allowed.		Use only clean (without nails, screws or sand particles) wood. No other material allowed.
			'''<big><u>Pallet wood, reclaimed flooring, reclaimed outdoor deck planks and any kind of wood used for concrete formwork is totally forbidden.</u></big>'''
	'''<big>~~The use of pallet~~ wood, reclaimed flooring, reclaimed outdoor deck planks and any kind of wood used for concrete formwork is totally forbidden.</big>'''

	==Spiral cutterhead==		==Spiral cutterhead==

4444: /* Handhavande av maskinen */

2023-11-06T20:14:37Z

Handhavande av maskinen

← Äldre version		Versionen från 6 november 2023 kl. 20.14
Rad 40:		Rad 40:

	==Handhavande av maskinen==		==Handhavande av maskinen==
	~~===Manual===~~

	Sprängskiss: [[:Fil:Scheppach hmc 3200 planing combi.pdf]]		Sprängskiss: [[:Fil:Scheppach hmc 3200 planing combi.pdf]]

	~~How to use the planer:~~		===Planer===

	1) By lifting the lever nearest the power button, rotate the table surface by lifting it up.		1) By lifting the lever nearest the power button, rotate the table surface by lifting it up.
Rad 60:		Rad 58:
	7) Turn the planer on by twisting the emergency button, and pressing the black power-button hard.		7) Turn the planer on by twisting the emergency button, and pressing the black power-button hard.

			=== '''Jointer''' ===
	~~How to use the jointer:~~

	1) Attach the fence to the jointer table.		1) Attach the fence to the jointer table.

4444: /* Dust collection instructions when planing */

2023-11-06T20:12:43Z

Dust collection instructions when planing

← Äldre version		Versionen från 6 november 2023 kl. 20.12
Rad 81:		Rad 81:

	'''<big>The use of pallet wood, reclaimed flooring, reclaimed outdoor deck planks and any kind of wood used for concrete formwork is totally forbidden.</big>'''		'''<big>The use of pallet wood, reclaimed flooring, reclaimed outdoor deck planks and any kind of wood used for concrete formwork is totally forbidden.</big>'''

	~~===Dust collection instructions when planing===~~

	~~Mount the yellow dust collector attachment when using it as a planer, and make sure it is connected to the central vacuum.~~

	~~===Dust collection instructions when jointing===~~

	~~Use the dust collector attachment that looks like a brown box. Set the table to 10.5-11 cm, enough for the box to fit and to still be able to adjust the in-feed table height.~~
	~~The box stays in place with some magnets. Connect the box to the central vacuum.~~

	==Spiral cutterhead==		==Spiral cutterhead==

4444: I added instructions to the planer/jointer.

2023-11-06T20:08:19Z

I added instructions to the planer/jointer.

← Äldre version		Versionen från 6 november 2023 kl. 20.08
Rad 30:		Rad 30:
	*Make adjustments with the machine powered off		*Make adjustments with the machine powered off
	*Check planer table before turning it on, a tool might have slipped under the cutter head		*Check planer table before turning it on, a tool might have slipped under the cutter head
	*Stock must be at least 30 cm long. Minimum 6 mm thick for jointer, 4 mm for ~~planning~~		*Stock must be at least 30 cm long. Minimum 6 mm thick for jointer, 4 mm for planing
	*Blades must be sharp. Dull blades will vibrate the stock and may cause a kickback.		*Blades must be sharp. Dull blades will vibrate the stock and may cause a kickback.
	*Clean tool and work area when done		*Clean tool and work area when done.
	*Feed the work so that the knives will cut “with the grain”. Use only stock that is free of knots and splits. Do not plane end grain		*Feed the work so that the knives will cut “with the grain”. Use only stock that is free of knots and splits. Do not plane end grain.
	*Use a push block when ~~planing~~ a flat surface. Never apply pressure directly over the knives with your hand.		*Use a push block when jointing a flat surface. Never apply pressure directly over the knives with your hand.
	*Do not plane the maximum amount off of stock when planing. Two passes through the planer can be better than one.		*Do not plane the maximum amount off of stock when planing. Two passes through the planer can be better than one.
	*When ~~planning~~ thin pieces of wood, be sure to stand to one side in case the wood breaks and kicks back.		*When planing thin pieces of wood, be sure to stand to one side in case the wood breaks and kicks back.
	*Support the work properly at the in feed and at the out feed.		*Support the work properly at the in feed and at the out feed.

Rad 42:		Rad 42:
	===Manual===		===Manual===

	Sprängskiss: [[:Fil:Scheppach hmc 3200 planing combi.pdf]]		Sprängskiss: [[:Fil:Scheppach hmc 3200 planing combi.pdf]]

			How to use the planer:

			1) By lifting the lever nearest the power button, rotate the table surface by lifting it up.

			2) Rotate the dust collection connection (the overhanging metal part) towards the table and pull the wooden handle so it snaps into place.

			3) Attach the yellow dust collection head to the dust collection connection. Fit it snugly and fully in, otherwise dust will sneak through the holes.

			4) Attach the central vacuum hose to the yellow dust collection head.

			5) Connect the power cord (located to the left of the door) to the planer. Push it in tightly.

			6) Before planing, make sure there is nothing on the planer table, that the vacuum is on, and that the feed roller lever is set to "1".

			7) Turn the planer on by twisting the emergency button, and pressing the black power-button hard.


			How to use the jointer:

			1) Attach the fence to the jointer table.

			2) Attach the brown dust collection box to the planer table at the same side you would be jointing from (the side farthest from the power button), and adjust the table height enough for the box to fit, approx. 11 cm. Then attach the central vacuum hose to the box.

			3) Adjust the cutter cover width enough for your stock to pass through.

			4) Using the lever, adjust the in-feed table height. It is highly recommended to start with a lower thickness and remove material in several passes.

			5) Connect the power cord (located to the left of the door) to the planer. Push it in tightly.

			6) Start the central vacuum, then start the jointer by twisting the emergency button and pressing the black power-button hard.

	===Material===		===Material===
	Endast för trä! Do to use wet or green wood. Wait 24 hours before planing glued wood pieces or pieces with epoxy.		Endast för trä! Only for wood! Do to use wet or green wood. Wait 24 hours before planing glued wood pieces or pieces with epoxy.

	Use only clean (without nails, screws or sand particles) wood. No other material allowed.		Use only clean (without nails, screws or sand particles) wood. No other material allowed.