Spånsug, Felder RL 125 - Versionshistorik

SamanFanni: Mycket

2025-11-06T22:43:24Z

Mycket

← Äldre version		Versionen från 6 november 2025 kl. 22.43
Rad 1:		Rad 1:
	==~~Generell~~ information==		==General information==
	[[Fil:Felder RL 125.jpg\|miniatyr]]The [https://www.felder-group.com/en-us/products/dust-extractors-c1963 Felder] RL 125 is a powerfull chip extractor connected to most of the machines in the woodshop. A sound absorber was added on top of the machine to keep the noise level acceptable. A combination of 100mm fixed pipes and flexible hoses with doors are used to direct the suction to the desired machine.		[[Fil:Felder RL 125.jpg\|miniatyr]]The [https://www.felder-group.com/en-us/products/dust-extractors-c1963 Felder] RL 125 is a powerfull chip extractor connected to most of the machines in the woodshop. A sound absorber was added on top of the machine to keep the noise level acceptable. A combination of 100mm fixed pipes and flexible hoses with doors are used to direct the suction to the desired machine.

	To use the vacuum, start the machine by turning the red knob and open the desired door connecting to the machine you are using. Check before starting it that all the other doors are closed in order to get the most flow~~. In a near future, the vacuum will turn ON and OFF automatically when opening/closing the doors~~.		To use the vacuum, start the machine by turning the red knob and open the desired door connecting to the machine you are using. Check before starting that all the other doors are closed in order to get the most flow.

	The vacuum should be used at anytime with the following machines:		The vacuum should be used at anytime with the following machines:

	*Table saw~~, table~~ router and planer ~~with~~ the ~~flexible~~ hose. ~~Use as well~~ to clean around ~~the miter saw and the lathe~~.		*Table saw (dedicated hose)
	*Band saw (~~one~~ dedicated ~~flexible~~ hose)		*Table router and planer/jointer use the same hose. You can use it to clean around them as well.
	*Miter saw (~~two~~ dedicated ~~pipes on the enclosure~~)		*Band saw (dedicated hose)
	*Beltsander (~~one~~ dedicated ~~flexible~~ hose)		*Miter saw (dedicated hose)
	*Lathe (one dedicated hose with large funnel ~~- under construction~~)		*Beltsander (dedicated hose)
			*Lathe (one dedicated hose with large funnel)

	It is not required to use the dust collection on the drill press~~, however it is useful when drilling large holes~~.		It is not required to use the dust collection on the drill press.


	Regularly check for the level of dust in the bag, and properly replace the plastic bag if needed. See instructions below.		Regularly check for the level of dust in the bag, and properly replace the plastic bag if needed. See instructions below.

	==~~Säkerhetsinformation~~==		==Safety information==
	''~~Saker man bör tänka på när man använder maskinen för att inte skada sig~~, ~~andra~~, ~~eller maskinen~~''		''Things to consider when using the machine to not hurt the machine, others, and yourself.''

	Not much risks of injuring yourself, but a few things to keep in mind to keep the machine running safely:		Not much risks of injuring yourself, but a few things to keep in mind to keep the machine running safely:
Rad 24:		Rad 25:
	*'''Do not cut or sand any wet wood as you could clog the filter (which is an expensive spare part)'''		*'''Do not cut or sand any wet wood as you could clog the filter (which is an expensive spare part)'''
	*'''Check the level of dust in the bag and change the bag when reaching the maximum level.'''		*'''Check the level of dust in the bag and change the bag when reaching the maximum level.'''
	*On the side of the machine, there is a handle that you can pull a few times to clean the filter, do not perform this when the machine is running.		*On the left side of the machine, there is a handle that you can pull a few times to clean the filter, do not perform this when the machine is running.
	*Do not obstruct the air output.		*Do not obstruct the air output.

	==Emptying the chip collector==		==Emptying the chip collector==
	[[Fil:Filter cleaning handle.jpg\|miniatyr]]		[[Fil:Filter cleaning handle.jpg\|miniatyr\|Pull the black handle a few times to clean the filter.]]
	~~[[Fil:Felder 2~~.~~jpg\|miniatyr~~]]
	To empty the chip collector:		To empty the chip collector:

	*Before changing the bag, turn off the machine and pull ~~4-5 time of the filter cleaning handle. The Filter cleaning handle is~~ the black handle on the ~~side of the machine on the lathe side~~. ~~See the upper picture~~ to the ~~right~~.		*Before changing the bag, turn off the machine and pull the black handle a few times to clean the filter. Wait a while to let the fine particles settle.
	*Pull the large handle upwards to lower the chip collector to the floor.		*Pull the large handle upwards to lower the chip collector to the floor.
	*Lift out the full bag and throw it in the garbage room.		*Lift out the full bag and throw it in the garbage room. (Take the keycard located in the cleaning closet outside the metalroom, and go to the garbage room which is the leftmost door on the truck loading dock out back. The door code is on the keycard.)
	*Take a new 200l bag from the ~~shelf above the wood lathe.~~		*Take a new 200l bag from the box on the ground next to the dust collector.
	*Do not cover the hole in the corner when replacing the bag. See the ~~lower picture~~ to the ~~right~~.
	*Roll in the collector and pull the handle down to lift it up and connect it. Make sure it is well aligned with the machine.		*Roll in the collector and pull the handle down to lift it up and connect it. Make sure it is well aligned with the machine.
	*Dispose of the full bag according to the instructions in [[Sophantering]]		*Dispose of the full bag according to the instructions in [[Sophantering]]

	~~<br />~~
	==Handhavande av maskinen==		==Handhavande av maskinen==

	===Manual===		===Manual===
	[https://www.yumpu.com/da/document/view/51465399/user-manual-dust-extractor-rl-125-rl-160-rl-200 Manual på Felder RL]		[https://www.yumpu.com/da/document/view/51465399/user-manual-dust-extractor-rl-125-rl-160-rl-200 Manual for Felder RL]

	===Material===		===Material===
	~~Endast för trä~~!		Only for wood! Metal chips may cause fires!
	~~===Användarinstruktioner===~~
	~~Se till att koppla in dammsugare innan du använder den~~!

	==Underhåll och reservdelar==		==Underhåll och reservdelar==
	===Underhåll===		===Underhåll===
Rad 75:		Rad 69:
	We do not have spare parts. Contact Felder directly to order more bags or a new filter.		We do not have spare parts. Contact Felder directly to order more bags or a new filter.

	#		We do have spare parts for the sprinkler heads. They should be in the locked maintenance drawer.

	==Logg==		==Logg==

			*2025-11-06: Sprinkler system added
	*2020-02-XX: Sound absorber added		*2020-02-XX: Sound absorber added
	*2019-12-XX: Inköpt		*2019-12-XX: Inköpt

	*

	==Länkar==		==Länkar==
Rad 94:		Rad 87:
	==Gallery==		==Gallery==
	<gallery>		<gallery>
	Fil:Felder 1.jpg\|Switch knob and handle for cleaning the filter		Fil:Felder 1.jpg\|Switch knob and handle for cleaning the filter. (Old woodroom)
	Fil:Felder 2.jpg\|Do not cover the hole when replacing the bag		Fil:Felder 2.jpg\|(Dated) Do not cover the hole when replacing the bag. (The hole exists to prevent the bag being sucked up into the filter. The hole allows a low pressure beneath the bag to keep it sucked down. This was replaced with a hose connected to the back.)
	Fil:Felder 4.jpg\|Dust collection for the bandsaw		Fil:Felder 4.jpg\|Dust collection for the bandsaw. (Old woodroom)
	Fil:Felder 3.jpg\|Floor swiping		Fil:Felder 3.jpg\|Floor swiping. (Old woodroom)
	Fil:Felder 5.jpg\|Connection to table saw and table router		Fil:Felder 5.jpg\|Connection to table saw and table router. (Old woodroom)
	Fil:Felder 6.jpg\|Dust collection for the miter saw		Fil:Felder 6.jpg\|Dust collection for the miter saw. (Old woodroom)
	</gallery>		</gallery>

	[[Kategori:Trärummet]]		[[Kategori:Trärummet]]

Jash: Added RL 125 Manual

2025-11-02T19:34:21Z

Added RL 125 Manual

← Äldre version		Versionen från 2 november 2025 kl. 19.34
Rad 86:		Rad 86:
	==Länkar==		==Länkar==
	https://www.felder-group.com/en-au/products/dust-extractors-extraction-units-c1963/clean-air-dust-extractor-performance-line-p144306		https://www.felder-group.com/en-au/products/dust-extractors-extraction-units-c1963/clean-air-dust-extractor-performance-line-p144306

	[[Fil:User Manual Dust Extractor RL 125 RL 160 RL 200.pdf]]		[[Fil:User Manual Dust Extractor RL 125 RL 160 RL 200.pdf]]

Jash den 2 november 2025 kl. 19.33

2025-11-02T19:33:54Z

← Äldre version		Versionen från 2 november 2025 kl. 19.33
Rad 86:		Rad 86:
	==Länkar==		==Länkar==
	https://www.felder-group.com/en-au/products/dust-extractors-extraction-units-c1963/clean-air-dust-extractor-performance-line-p144306		https://www.felder-group.com/en-au/products/dust-extractors-extraction-units-c1963/clean-air-dust-extractor-performance-line-p144306
			[[Fil:User Manual Dust Extractor RL 125 RL 160 RL 200.pdf]]

	==Ägare==		==Ägare==

Philon-: Kategori:Trärummet

2022-04-14T22:00:32Z

Kategori:Trärummet

← Äldre version		Versionen från 14 april 2022 kl. 22.00
Rad 99:		Rad 99:
	Fil:Felder 6.jpg\|Dust collection for the miter saw		Fil:Felder 6.jpg\|Dust collection for the miter saw
	</gallery>		</gallery>

			[[Kategori:Trärummet]]

Tomas: Added link to how to dispose of full bags

2020-11-25T10:06:08Z

Added link to how to dispose of full bags

← Äldre version		Versionen från 25 november 2020 kl. 10.06
Rad 38:		Rad 38:
	*Do not cover the hole in the corner when replacing the bag. See the lower picture to the right.		*Do not cover the hole in the corner when replacing the bag. See the lower picture to the right.
	*Roll in the collector and pull the handle down to lift it up and connect it. Make sure it is well aligned with the machine.		*Roll in the collector and pull the handle down to lift it up and connect it. Make sure it is well aligned with the machine.
			*Dispose of the full bag according to the instructions in [[Sophantering]]

	<br />		<br />
Rad 69:		Rad 70:
	**Check whether the seal between dust collector and unit is broken, replace if needed		**Check whether the seal between dust collector and unit is broken, replace if needed
	*TODO		*TODO
	**~~Automatisation~~ of the dust collection system		**Automation of the dust collection system

	===Reservdelar===		===Reservdelar===

Cloraux: /* Generell information */

2020-11-13T10:45:11Z

Generell information

← Äldre version		Versionen från 13 november 2020 kl. 10.45
Rad 2:		Rad 2:
	[[Fil:Felder RL 125.jpg\|miniatyr]]The [https://www.felder-group.com/en-us/products/dust-extractors-c1963 Felder] RL 125 is a powerfull chip extractor connected to most of the machines in the woodshop. A sound absorber was added on top of the machine to keep the noise level acceptable. A combination of 100mm fixed pipes and flexible hoses with doors are used to direct the suction to the desired machine.		[[Fil:Felder RL 125.jpg\|miniatyr]]The [https://www.felder-group.com/en-us/products/dust-extractors-c1963 Felder] RL 125 is a powerfull chip extractor connected to most of the machines in the woodshop. A sound absorber was added on top of the machine to keep the noise level acceptable. A combination of 100mm fixed pipes and flexible hoses with doors are used to direct the suction to the desired machine.

	To use the vacuum, start the machine by turning the red knob and open the desired door connecting to the machine you are using. Check before starting it that all the other doors are closed in order to get the most flow. In a near ~~futur~~, the vacuum will turn ON and OFF automatically when opening/closing the doors.		To use the vacuum, start the machine by turning the red knob and open the desired door connecting to the machine you are using. Check before starting it that all the other doors are closed in order to get the most flow. In a near future, the vacuum will turn ON and OFF automatically when opening/closing the doors.

	The vacuum should be used at anytime with the following machines:		The vacuum should be used at anytime with the following machines:
Rad 8:		Rad 8:
	*Table saw, table router and planer with the flexible hose. Use as well to clean around the miter saw and the lathe.		*Table saw, table router and planer with the flexible hose. Use as well to clean around the miter saw and the lathe.
	*Band saw (one dedicated flexible hose)		*Band saw (one dedicated flexible hose)
	*Miter saw (two dedicated pipes)		*Miter saw (two dedicated pipes on the enclosure)
	*Beltsander (one dedicated flexible hose)		*Beltsander (one dedicated flexible hose)
			*Lathe (one dedicated hose with large funnel - under construction)

	It is not required to use the dust collection on the drill press, however it is useful when drilling large holes.		It is not required to use the dust collection on the drill press, however it is useful when drilling large holes.

	~~<s>Near the belt sander, a pipe goes all the way to the floor and make the floor cleaning really easy.</s> <br />~~

	Regularly check for the level of dust in the bag, and properly replace the plastic bag if needed. See instructions below.		Regularly check for the level of dust in the bag, and properly replace the plastic bag if needed. See instructions below.
Rad 32:		Rad 32:
	To empty the chip collector:		To empty the chip collector:

	*Before changing the bag, turn off the machine and pull 4-5 time of the filter cleaning handle. The Filter cleaning handle is the black handle on the side of the machine~~, under~~ the ~~power connector~~. See the upper picture to the right.		*Before changing the bag, turn off the machine and pull 4-5 time of the filter cleaning handle. The Filter cleaning handle is the black handle on the side of the machine on the lathe side. See the upper picture to the right.
	*Pull the large handle upwards to lower the chip collector to the floor.		*Pull the large handle upwards to lower the chip collector to the floor.
	*Lift out the full bag and ~~trhow~~ it in the garbage room.		*Lift out the full bag and throw it in the garbage room.
	*Take a new 200l bag from the shelf above the wood lathe.		*Take a new 200l bag from the shelf above the wood lathe.
	*Do not cover the hole in the corner when replacing the bag. See the lower picture to the right.		*Do not cover the hole in the corner when replacing the bag. See the lower picture to the right.
Rad 69:		Rad 69:
	**Check whether the seal between dust collector and unit is broken, replace if needed		**Check whether the seal between dust collector and unit is broken, replace if needed
	*TODO		*TODO
	**Add a door and a double connection to the belt sander and the drill press
	**Automatisation of the dust collection system		**Automatisation of the dust collection system
	***24V relay + tempo

	===Reservdelar===		===Reservdelar===

ArmyAntSEC den 2 juli 2020 kl. 12.18

2020-07-02T12:18:52Z

← Äldre version		Versionen från 2 juli 2020 kl. 12.18
Rad 29:		Rad 29:
	==Emptying the chip collector==		==Emptying the chip collector==
	[[Fil:Filter cleaning handle.jpg\|miniatyr]]		[[Fil:Filter cleaning handle.jpg\|miniatyr]]
	To empty the chip ~~colector~~:		[[Fil:Felder 2.jpg\|miniatyr]]
			To empty the chip collector:

	*Before changing the bag, turn off the machine and pull 4-5 time of the filter cleaning handle. The Filter cleaning handle is the black handle on the side of the machine, under the power connector. See the picture to the right.		*Before changing the bag, turn off the machine and pull 4-5 time of the filter cleaning handle. The Filter cleaning handle is the black handle on the side of the machine, under the power connector. See the upper picture to the right.
	*Pull the large handle upwards to lower the chip collector to the floor.		*Pull the large handle upwards to lower the chip collector to the floor.
	*Lift out the full bag and trhow it in the garbage room.		*Lift out the full bag and trhow it in the garbage room.
	*Take a new 200l bag from the shelf above the wood lathe.		*Take a new 200l bag from the shelf above the wood lathe.
	*Do not cover the hole in the corner when replacing the bag ~~(see~~ picture in the ~~gallery below)~~.		*Do not cover the hole in the corner when replacing the bag. See the lower picture to the right.
	*Roll in the collector and pull the handle down to lift it up and connect it. Make sure it is well aligned with the machine.		*Roll in the collector and pull the handle down to lift it up and connect it. Make sure it is well aligned with the machine.

Cloraux: /* Generell information */

2020-06-29T07:01:24Z

Generell information

← Äldre version		Versionen från 29 juni 2020 kl. 07.01
Rad 13:		Rad 13:
	It is not required to use the dust collection on the drill press, however it is useful when drilling large holes.		It is not required to use the dust collection on the drill press, however it is useful when drilling large holes.

	Near the belt sander, a pipe goes all the way to the floor and make the floor cleaning really easy. <br />		<s>Near the belt sander, a pipe goes all the way to the floor and make the floor cleaning really easy.</s> <br />

	Regularly check for the level of dust in the bag, and properly replace the plastic bag if needed. See instructions below.		Regularly check for the level of dust in the bag, and properly replace the plastic bag if needed. See instructions below.

Cloraux: /* Generell information */

2020-06-29T07:01:05Z

Generell information

← Äldre version		Versionen från 29 juni 2020 kl. 07.01
Rad 12:		Rad 12:

	It is not required to use the dust collection on the drill press, however it is useful when drilling large holes.		It is not required to use the dust collection on the drill press, however it is useful when drilling large holes.


	Near the belt sander, a pipe goes all the way to the floor and make the floor cleaning really easy. <br />		Near the belt sander, a pipe goes all the way to the floor and make the floor cleaning really easy. <br />

Cloraux: /* Generell information */

2020-06-29T07:00:50Z

Generell information

← Äldre version		Versionen från 29 juni 2020 kl. 07.00
Rad 9:		Rad 9:
	*Band saw (one dedicated flexible hose)		*Band saw (one dedicated flexible hose)
	*Miter saw (two dedicated pipes)		*Miter saw (two dedicated pipes)
			*Beltsander (one dedicated flexible hose)

			It is not required to use the dust collection on the drill press, however it is useful when drilling large holes.

	~~In a near futur, the belt sander and drill press will have a dedicated hose too.~~

	Near the belt sander, a pipe goes all the way to the floor and make the floor cleaning really easy. <br />		Near the belt sander, a pipe goes all the way to the floor and make the floor cleaning really easy. <br />

	Regularly check for the level of dust in the bag, and properly replace the plastic bag if needed. See instructions below.		Regularly check for the level of dust in the bag, and properly replace the plastic bag if needed. See instructions below.

	==Säkerhetsinformation==		==Säkerhetsinformation==
	''Saker man bör tänka på när man använder maskinen för att inte skada sig, andra, eller maskinen''		''Saker man bör tänka på när man använder maskinen för att inte skada sig, andra, eller maskinen''