ArmyAntSEC den 17 juni 2024 kl. 18.22

2024-06-17T18:22:52Z

← Äldre version		Versionen från 17 juni 2024 kl. 18.22
Rad 80:		Rad 80:
	* When using the movable table, walk with it, do not stand still and lean forward.		* When using the movable table, walk with it, do not stand still and lean forward.
	* '''Let everyone try this'''		* '''Let everyone try this'''
	* You can also attach an uneven piece of wood length-wise on the moving table to give it a first clean cut. Use clamps and the t-slow to fasten the piece.

	= Replacing the blade (Not part of the basic walk-through) =		= Replacing the blade (Not part of the basic walk-through) =

ArmyAntSEC: Skapade sidan med 'Complete walk-through of the wood-room intro, and table saw safety course. = Work-bench area = * The workbenches are on wheels so they can be moved around. * The corner is for 48h storage for drying glue. Mark items you put there with a temporary-storage sticker. The table can be folded down for larger items. ** Items older than 48h can be moved out of the way. * In the roof there is an air-dust filter. The remote is by the door. Start it with a timer so it shuts...'

2024-06-10T18:28:30Z

Skapade sidan med 'Complete walk-through of the wood-room intro, and table saw safety course. = Work-bench area = * The workbenches are on wheels so they can be moved around. * The corner is for 48h storage for drying glue. ** Mark items you put there with a temporary-storage sticker. ** The table can be folded down for larger items. ** Items older than 48h can be moved out of the way. * In the roof there is an air-dust filter. The remote is by the door. Start it with a timer so it shuts...'

Ny sida

Complete walk-through of the wood-room intro, and table saw safety course.

= Work-bench area =

* The workbenches are on wheels so they can be moved around.
* The corner is for 48h storage for drying glue.
** Mark items you put there with a temporary-storage sticker.
** The table can be folded down for larger items.
** Items older than 48h can be moved out of the way.
* In the roof there is an air-dust filter. The remote is by the door. Start it with a timer so it shuts off automatically.
* The Lathe is in this work area, if someone is using it, make sure not to bump into them.
* None of the tools should ever leave the wood-room.

= Dust collection =

* The dust collector turns on automatically whenever a valve is opened.
* Has a box on the floor by the lathe to sweep floor-dust into.
* If you are the last person to leave the room, you must check that the dust collector is off. Running it all night is a fire hazard.
* Before you start and when you are done, do the following:
** Pull the handle on the side to clear the filter
** Check that the dust is not above the middle of the window. If it is, empty and replace the bag.
** New bags can be found near the mitre saw.

= Storage =

* There is temporary (2 months) storage along the walls.
* Usable pieces can be placed near the mitre saw for others to use.
* The planar has a protective cover so you can put items on it while working.
** No gluing or working on any of the machine surfaces.
* Everything on the floor, not counting the glue-dry area, is free-use.
* Remember that we have a storage room.

= Table saw =

== Do-nots ==

* Do not use any blade other than those provided by the Makerspace. The saw uses custom blades because it has a motor break.
* Do not stand right in front of the blade. Hold the wood on one side of the blade and stand on that side. The other side can come flying back.
* Never, ever, remove the riving knife behind the blade. It is the most important safety feature. There are ways to use a table saw without such a blade. If you want to do that, get your own table saw.
* Do not remove the conventional fence. It can be pushed far enough to the side for any normal use.
* Do not back out of a cut half-way. Either finish the cut, or hold still and turn off the machine.
* Do not adjust or disassemble the cross-cut fence. We have ordered parts to build an adjustable cross-cut fence.
* Do not hold a piece of wood with just your hands to cut it. Use the fences to slide it.

== Basic operation ==

* There exists a loose handle that is used to adjust the blade in/down and angle it.
* For the angle, there is a fastening screw.
** Only really needed at around 22 degrees angle.
** There is a stop that is close enough to 90 degrees.
* The on/off switch is a bit hard to see and reach. Learn where the off-switch is before starting to use the machine.
* Turn the chip evacuator on before starting the machine.
* Make sure the blade is raised about 10mm above the top of your work surface.
* When you stop the machine, you will hear a buzzing of the break for a few seconds after the blade has stopped. This is normal.

== Cutting pieces that are longer than they are wide ==

* Use the traditional fence
* Make sure the traditional fence is moved back so it covers the entire blade and a bit more.
* For wide pieces (20+cm)
** Stand between the blade and the fence.
** Hold the wood with your hands between the blade and the fence and push it until the piece is completely cut through.
* For thinner cuts
** Get two push-sticks.
** Place one on the table and use the other to push the piece of wood down and towards the fence.
** Use the other hand to push the wood forward until the wood is completely on the table.
** Use the second push-stick to push the wood to finish the cut.
** '''Let everyone try this.'''
* The traditional fence can be flipped on its side to become very low for work on pieces that are very low and thin.

== Cutting pieces that are wider than they are long ==

* Use the sliding table and the cross-fence
* Attach the 90 degree fence to the sliding table.
* It can be extended, and also has a stop to make pieces of the same length
* If using the traditional fence as a stop, pull it back so it does not cover the blade. If it covers the blade, pieces can fly.
* Unlock the moving table via the handle on its side
* Stand right up against the moving table. To the side of the blade, you are safe.
* Pull the table back and place your piece. Hold it agains the fence and make the cut.
* When using the movable table, walk with it, do not stand still and lean forward.
* '''Let everyone try this'''
* You can also attach an uneven piece of wood length-wise on the moving table to give it a first clean cut. Use clamps and the t-slow to fasten the piece.

= Replacing the blade (Not part of the basic walk-through) =

* Pull the sliding table all the way back
* Move the knob on the far side of the machine all the way down. This stops the machine from starting.
* Slide the black protective metal plate out and put it to the side.
* Unscrew the blade with an allen-wrench and a hex wrench
* Replace the blade and screw it back
* Slide the black black protective metal plate back in place.
** It has slots on either side it slides in.
** To get it in all the way, it needs to be lifted a bit.
* Move the know back to the middle position (The machine will not start if it is in the top or bottom positions)
* Pull the sliding table back to its default position.

Wood room intro and table saw safety - Versionshistorik

ArmyAntSEC den 17 juni 2024 kl. 18.22