Bordssåg, Hammer K3 Winner
| You must complete the online course before using this machine |
Introduction video
Generell information
| Snabbfakta Bordssåg, Hammer K3 Winner |
| Användning: Kräver kurs |
| Modell: Hammer K3 Winner |
| Bokning: Först till kvarn |
| Kostnad: Fri |
| Loggning: Inget |
| Plats: Trärummet |
Bordssåg, Hammer K3 Winner. En stor bordssåg med gjutjärnsbord.
Säkerhetsinformation
- Wear safety glasses and turn on the dust extractor
- The Riving Knife is the most important safety feature and may not be removed
- Do not use any blades not provided by the Makerspace. The saw has special holes to accomodate the motor break.
- Do not use Dado-stacks (https://en.wikipedia.org/wiki/Dado_set)
- Never cut stock free hand
- Be certain that the blade is sharp
- Set the blade so that it extends no more than 10 mm above the stock to be cut
- Stand to one side of the operation blade, do not reach across it
- Make sure that the stock is fully past the blade before turning the saw off
- Keep hands at least 15 cm from the blade. Use push sticks when cutting closer
- Rough stock must be surfaced and at least one side jointed before being cut
- Use only new stock that is free of knots, splits and warp
- Use a push stick to push small scrap away
- Cross cutting on the table saw is dangerous. 30 cm cross-cuts or under should be made on the BOSCH sliding compound miter saw
- As you complete your work, turn off the saw and remain until the blade has stopped
- Clear the saw of dust and waste. Return the saw blade to zero settings. Sweep the work area!
Handhavande av maskinen
Material
| Material | Godkänd | Kommentar |
|---|---|---|
| Massivt trä | Ja | Om du kan garantera att materialet inte innehåller spikar eller skruvar |
| Spånskiva | Ja | |
| MDF | Ja | |
| Laminatgolv | Nej | Det räcker med att du sågar 20cm i materialet för att göra klingan obrukbar. Riskerar att förstöra sågen. |
| Plywood | Ja | |
| Laminerade skivor (MDF, Spånskiva osv.) | Ja | Sliter mycket på klingan och för bra resultat behövs oftast en klinga med många tänder och rätt vinkel på tänderna. |
| Tryckimpregnerat/Pressure treated wood | Nej | Dust is not safe in our closed environment. |
| Metall | Nej | All form av metall är helt förbjuden. Klingan får inte bytas till metallklinga. |
| Stone (lightweight chalk, limestone, ...) | Nej | Inga stenlika material tillåts då de förstör klingan och det vassa dammet förstör maskinen. |
Användarinstruktioner
Se till att slå på spånsugen innan du använder den!
Förbrukningsmaterial
We have some spare blades. When a blade does not cut properly, change the blade and label it "Dull" and store it until we have enough of them to bring to resharpening.
Underhåll och reservdelar
Underhåll
- Daily
- Visual check whether unit or parts are damaged
- Check whether power cable is damaged
- Check if the riving knife is installed and raised enough.
- Annually
- Deep cleaning of the machine, adjusting of the top plates
Logg
2025-01-05:
Table saw cleaned throughly, was full of saw dust as the hose and adapter were disconnected. Adapter was broken and a new one is being printed.
Cleaned and lubricated the height spindle. It still feels like it's hard to adjust upward, but not affecting the performance or operation of the machine.
Cleaned and lubricated tilting spindle. There is a clicking sound at around 40 degrees. Unclear what.
Checked the drive and scoring belt. Found OK
The blade is aligned to 90+/-0.1 degrees. Parallel fence is, as far as we could tell, parallel to the blade. The cross cut fence is, as far as we can tell, 90 degrees to the blade. Slight wobble on the crosscut fence so you have to be careful.
Länkar
Instruktionsvideo för hur man använder en bordssåg.
My Top 4 Table Saw Jigs & Accessories: How to Make Them - Pask Makes