Plan- och rikthyvel, Scheppach HMC 3200: Skillnad mellan sidversioner

Från Stockholm Makerspace Wiki
Ingen redigeringssammanfattning
Rad 23: Rad 23:


==Generell information==
==Generell information==
Sågen kan vinklas 52° Vänster till 60° Höger i förhållande till anhållet i bakkant (geringsvinkel)
<br />
 
Sågen kan vinklas 47° Vänster till 2° Höger i förhållande till bordet (snedkapningsvinkel)
 
 
This saw can be used to cut relatively large pieces of wood and is ideal to make cross-cuts. It is set for square, miter and bevel cuts, or a combination of miter and bevel cuts (compound cut).
 
The saw is attached to the table with 4 screws and some angle combinations are unavailable due to the present configuration.
 
It is possible to unscrew the saw and move it to perform special cuts or to cut longer pieces. The saw must be set back to it's initial position.
 
 
This saw can be use to perform non-through cuts (Dados, Grooves & Rabbets) using the depth stop. For such operation, it's usually required to install a sacrificial fence (see pictures in the galerie)
==Säkerhetsinformation==
==Säkerhetsinformation==


Rad 42: Rad 30:
*Check planer table before turning it on, a tool might have slipped under the cutter head
*Check planer table before turning it on, a tool might have slipped under the cutter head
*Stock must be at least 30 cm long. Minimum 6 mm thick for jointer, 4 mm for planning
*Stock must be at least 30 cm long. Minimum 6 mm thick for jointer, 4 mm for planning
*Blades must be sharp. Dull blades will vibrate the stock and may cause a kickback.  
*Blades must be sharp. Dull blades will vibrate the stock and may cause a kickback.
*Clean tool and work area when done
*Clean tool and work area when done
*Feed the work so that the knives will cut “with the grain”. Use only stock that is free of knots and splits. Do not plane end grain
*Feed the work so that the knives will cut “with the grain”. Use only stock that is free of knots and splits. Do not plane end grain
*Use a push block when planing a flat surface. Never apply pressure directly over the knives with your hand.  
*Use a push block when planing a flat surface. Never apply pressure directly over the knives with your hand.
*Do not plane the maximum amount off of stock when planing. Two passes through the planer can be better than one.  
*Do not plane the maximum amount off of stock when planing. Two passes through the planer can be better than one.
*When planning thin pieces of wood, be sure to stand to one side in case the wood breaks and kicks back.  
*When planning thin pieces of wood, be sure to stand to one side in case the wood breaks and kicks back.
*Support the work properly at the in feed and at the out feed.  
*Support the work properly at the in feed and at the out feed.
 




Rad 55: Rad 42:
===Manual===
===Manual===


[https://www.bosch-professional.com/binary/ocsmedia/optimized/full/o290859v21_160992A4D3_201808.pdf Manual på Boschs hemsida]  
Sprängskiss: [[:Fil:Scheppach hmc 3200 planing combi.pdf]]  


===Material===  
===Material===  
Endast för trä!   
Endast för trä! Do to use wet or green wood. Wait 24 hours before planing glued wood pieces.  


Some plastics can be cut using this saw, but you need to use your own dedicated blade. Always disconnect the power before changing the blade and make sure it's properly centered before starting the saw.  
Use only clean (without nails, screws or sand particles) wood. No other material allowed.
===Användarinstruktioner===
===Användarinstruktioner===
Se till att koppla in dammsugare innan du använder den!
Se till att koppla in dammsugare innan du använder den!
Rad 67: Rad 54:


==Förbrukningsmaterial==
==Förbrukningsmaterial==
We currently have XX spare blades for the miter saw. These blade can be resharpened, do not throw them away, instead label them as "DULL".
We currently have 3 sets of blades. Label and store the dull blades. When two sets are dull, send them to resharpening.  
 
The blades provided by the makerspace are for general purpose and designed for cross-cutting and have about XX teeth.
 
You can buy and install your own blade for some specific projects (cutting plastics, Flat kerf blades for joinery, etc) but you must install back the original blade when you are done.  
 
Klingdiameter: 216 mm
 
Klinghåls-Ø: 30 mm


==Underhåll och reservdelar==
==Underhåll och reservdelar==
Rad 84: Rad 63:
**Visual check whether unit or parts are damaged
**Visual check whether unit or parts are damaged
**Check whether power cable is damaged
**Check whether power cable is damaged
**Vacuum and clean the saw and the dust collection box. Throw away scrap wood.
**Check if there is any parts loose around the blades before plugging and running it.  


*Monthly
*Monthly
**Check the blade sharpness. Change blade if necessary.
**Check the blade sharpness. Change blade if necessary.  
**Clean the laser plastic cover and remove gunk and dust on the saw.
*Annually
**Remove the front cover to clean and grease the transmission chain and clean the clutch plates.
*TODO
**Built a side fence for the jointer [[:Fil:Rikthyvel.pdf]]


===Reservdelar===
===Reservdelar===
Rad 111: Rad 93:


==Gallery==
==Gallery==
<gallery>
Fil:MiterSaw.jpg|Cross-cutting large solid planks
</gallery>
[[Fil:Scheppach_hmc_3200.jpg|400px|thumb|left|Scheppach HMC 3200]]
Planyveln (Den undre) fungerar bra.
Rikthyveln (Den övre) saknar anhåll och är därför inte så användbar.


Ritningsförslag på rikthyvel: [[Fil:Rikthyvel.pdf|miniatyr]]
Ritningsförslag på rikthyvel:[[Fil:Rikthyvel.pdf|miniatyr]]


Sprängskiss: [[Fil:Scheppach_hmc_3200_planing_combi.pdf]]
Sprängskiss: [[Fil:Scheppach_hmc_3200_planing_combi.pdf]]

Versionen från 25 februari 2020 kl. 23.29

Snabbfakta Bosch GCM8 SJL
Modell: Scheppach HMC 3200
Bokningsbar: Nej
Kostnad att använda: Gratis
Info 1: Kap- och gersåg
Arbetsyta: 32 cm
Obelastad hastighet: - RPM
Märkeffekt: - W


Generell information


Säkerhetsinformation

  • Wear safety glasses, keep hands at least 15 cm from the cutterhead
  • Make adjustments with the machine powered off
  • Check planer table before turning it on, a tool might have slipped under the cutter head
  • Stock must be at least 30 cm long. Minimum 6 mm thick for jointer, 4 mm for planning
  • Blades must be sharp. Dull blades will vibrate the stock and may cause a kickback.
  • Clean tool and work area when done
  • Feed the work so that the knives will cut “with the grain”. Use only stock that is free of knots and splits. Do not plane end grain
  • Use a push block when planing a flat surface. Never apply pressure directly over the knives with your hand.
  • Do not plane the maximum amount off of stock when planing. Two passes through the planer can be better than one.
  • When planning thin pieces of wood, be sure to stand to one side in case the wood breaks and kicks back.
  • Support the work properly at the in feed and at the out feed.


Handhavande av maskinen

Manual

Sprängskiss: Fil:Scheppach hmc 3200 planing combi.pdf

Material

Endast för trä! Do to use wet or green wood. Wait 24 hours before planing glued wood pieces.

Use only clean (without nails, screws or sand particles) wood. No other material allowed.

Användarinstruktioner

Se till att koppla in dammsugare innan du använder den!

Skriv något om hur man ställer de olika vinklarna

Förbrukningsmaterial

We currently have 3 sets of blades. Label and store the dull blades. When two sets are dull, send them to resharpening.

Underhåll och reservdelar

Underhåll

  • Daily
    • Visual check whether unit or parts are damaged
    • Check whether power cable is damaged
    • Check if there is any parts loose around the blades before plugging and running it.
  • Monthly
    • Check the blade sharpness. Change blade if necessary.
  • Annually
    • Remove the front cover to clean and grease the transmission chain and clean the clutch plates.
  • TODO

Reservdelar

We do not have spare parts for this machine.

Logg

  • 2020-02-XX: Miter saw station build next to the dust collector.
  • 2019-10-05: Inköpt

Länkar

https://www.bosch-professional.com/se/sv/products/gcm-8-sjl-0601B19100

8 Miter Saw Pro Tips & Tricks - Steve Ramsey - Woodworking for Mere Mortals

Ägare

Maskinen inköpt av Makerspace

Gallery

Ritningsförslag på rikthyvel:Fil:Rikthyvel.pdf

Sprängskiss: Fil:Scheppach hmc 3200 planing combi.pdf