278
redigeringar
Ultimonster: Skillnad mellan sidversioner
ingen redigeringssammanfattning
DanielS (diskussion | bidrag) Ingen redigeringssammanfattning |
Philon- (diskussion | bidrag) Ingen redigeringssammanfattning |
||
| (9 mellanliggande sidversioner av 5 användare visas inte) | |||
| Rad 1: | Rad 1: | ||
== Introduction / Background == | {{museum}} | ||
==Introduction / Background== | |||
In August 2013, a heavily modified Ultimaker 3D printer was put up for sale on the Ultimaker forums (in[http://umforum.ultimaker.com/index.php?/topic/2668-assembled-upgraded-ultimaker-for-sale-germany/?hl=%2Bultimaker+%2Bfor+%2Bsale this thread]). | In August 2013, a heavily modified Ultimaker 3D printer was put up for sale on the Ultimaker forums (in[http://umforum.ultimaker.com/index.php?/topic/2668-assembled-upgraded-ultimaker-for-sale-germany/?hl=%2Bultimaker+%2Bfor+%2Bsale this thread]). | ||
| Rad 8: | Rad 10: | ||
[[Fil:crowdfundedultimaker.jpg|right|300px|The heavily modified Ultimaker]] | [[Fil:crowdfundedultimaker.jpg|right|300px|The heavily modified Ultimaker]] | ||
{|class="wikitable" | {| class="wikitable" | ||
!Funder | !Funder | ||
!Amount (SEK) | !Amount (SEK) | ||
|- | |- | ||
|Daniel Sjöstrand | |Daniel Sjöstrand | ||
|1000 | |1000 | ||
|- | |- | ||
| Rad 45: | Rad 47: | ||
|500 | |500 | ||
|- | |- | ||
|Anders | |Anders Henschen | ||
|500 | |500 | ||
|- | |- | ||
| Rad 76: | Rad 78: | ||
|} | |} | ||
We still have some money to purchase extra accessories for the printer. | We still have some money to purchase extra accessories for the printer. | ||
The currency rate at time of purchase was 8.76 SEK to 1 EUR, so 1337EUR = 11 712 SEK. | |||
This means we still have 13200-11712 SEK = 1488SEK to purchase spare parts / upgrades etc for. | |||
== Change Log == | ==Specifications== | ||
*Ultimaker rev.3 from Feb 2013. | |||
*UltiController with custom firmware (version?). | |||
*Heated aluminum bed with silicone heat pad | |||
*Active cooled full-metal E3D-style hotend | |||
**2.85/3.0mm filament size | |||
**0.4mm nozzle size | |||
==Print settings== | |||
It would be nice if we can keep track of print settings and results here. | |||
===Andreas first prints 2013-11-26=== | |||
Used Cura 13.11 (on my laptop) and printed two small (~4x4x2 & ~8x5x2 cm) gingerbread cutters with 3dverkstan PLA filament. Very happy with my first print on this machine, except maybe retraction so a few strings had to be cut off afterwards. | |||
*Basic: Layer height=0.2, Shell thickness=0.8, Enable retraction=Y, Botton/Top fill=0.4, Fill density=30%, Print speed=50mm/s, Print temperature=210, Bed temperature=60, Support=None, Platform adhesion type=Brim, Filament diameter=2.85, Flow=100% | |||
*Advanced: Nozzle: 0.4, Retraction speed=40, Distance 4.5, Initial layer=0.3, Cut off object bottom=0, Dual extrusion overlap=0.2, Speed travel=150, Bottom layer speed=20, Infill speed=0, Minimal layer time=5, Enable cooling fan=Y | |||
*Start g-code: http://pastebin.com/SYAEtuP9 | |||
*End g-code: http://pastebin.com/urSF5dci | |||
==Troubleshooting== | |||
Hints from Daniel S: | |||
*The biggest risk for getting a big jam in the extruder is keep the extruder warn too long without running. Then the heat can spread upward and make a blockage. | |||
*When changing between ABS and PLA you need to make sure to remove all ABS-remains to avoid jamming. Some manual extruding may be necessary. The easiest would be to have two 3d printers: one for PLA and one for ABS. | |||
Also see: | |||
*http://wiki.ultimaker.com/Troubleshooting | |||
*http://wiki.ultimaker.com/Jamming | |||
== History == | |||
The printer had quite a few problems, including the hotend melting and other problems. It broke down in August 2014, and a rebuild/upgrade process started, but were in the end never finished. It never printed again before it finally was scrapped in August 2020. | |||
==Change Log == | |||
The below is a Change Log which we all should use while putting the Ultimaker into operation and learning it. | The below is a Change Log which we all should use while putting the Ultimaker into operation and learning it. | ||
After the major work has been done, this can be moved to a "history" section and instead we should put up instructions for use here. | After the major work has been done, this can be moved to a "history" section and instead we should put up instructions for use here. | ||
{|class="wikitable" | {| class="wikitable" | ||
! align="top"| Date | ! align="top" |Date | ||
!Description | !Description | ||
!Who | !Who | ||
| Rad 95: | Rad 136: | ||
After a while | After a while | ||
|DanielS | |DanielS | ||
|- | |||
|2018-04-21 | |||
|The machine has been unused for some time (at least one to two years). One of the Ultimaker 2 machines had a problem with at least one bent and possibly otherwise damaged rods. Two rods were reused from the Ultimonster and the old ones that aren´t straight anymore are placed lieing in the Ultimonster. | |||
|Christoffer J | |||
|- | |||
|2020-08-14 | |||
|The Ultimonster is no more, it was disassembled and gutted for parts, the frame ended up in the garbage. | |||
|Erik C | |||
|} | |} | ||