Bordssåg, Hammer K3 Winner: Skillnad mellan sidversioner

VisuellWikitext

Nuvarande version från 22 november 2024 kl. 12.10

You must complete the online course before using this machine

Introduction video

Generell information

Snabbfakta Bordssåg, Hammer K3 Winner

Användning: Kräver kurs

Modell: Hammer K3 Winner

Bokning: Först till kvarn

Kostnad: Fri

Loggning: Inget

Plats: Trärummet

Bordssåg, Hammer K3 Winner. En stor bordssåg med gjutjärnsbord.

Säkerhetsinformation

Wear safety glasses and turn on the dust extractor
The Riving Knife is the most important safety feature and may not be removed
Do not use any blades not provided by the Makerspace. The saw has special holes to accomodate the motor break.
Do not use Dado-stacks (https://en.wikipedia.org/wiki/Dado_set)
Never cut stock free hand
Be certain that the blade is sharp
Set the blade so that it extends no more than 10 mm above the stock to be cut
Stand to one side of the operation blade, do not reach across it
Make sure that the stock is fully past the blade before turning the saw off
Keep hands at least 15 cm from the blade. Use push sticks when cutting closer
Rough stock must be surfaced and at least one side jointed before being cut
Use only new stock that is free of knots, splits and warp
Use a push stick to push small scrap away
Cross cutting on the table saw is dangerous. 30 cm cross-cuts or under should be made on the BOSCH sliding compound miter saw
As you complete your work, turn off the saw and remain until the blade has stopped
Clear the saw of dust and waste. Return the saw blade to zero settings. Sweep the work area!

Handhavande av maskinen

Material

Material	Godkänd	Kommentar
Massivt trä	Ja	Om du kan garantera att materialet inte innehåller spikar eller skruvar
Spånskiva	Ja
MDF	Ja
Laminatgolv	Nej	Det räcker med att du sågar 20cm i materialet för att göra klingan obrukbar. Riskerar att förstöra sågen.
Plywood	Ja
Laminerade skivor (MDF, Spånskiva osv.)	Ja	Sliter mycket på klingan och för bra resultat behövs oftast en klinga med många tänder och rätt vinkel på tänderna.
Tryckimpregnerat/Pressure treated wood	Nej	Dust is not safe in our closed environment.
Metall	Nej	All form av metall är helt förbjuden. Klingan får inte bytas till metallklinga.
Stone (lightweight chalk, limestone, ...)	Nej	Inga stenlika material tillåts då de förstör klingan och det vassa dammet förstör maskinen.

Användarinstruktioner

Se till att slå på spånsugen innan du använder den!

Förbrukningsmaterial

We have some spare blades. When a blade does not cut properly, change the blade and label it "Dull" and store it until we have enough of them to bring to resharpening.

Underhåll och reservdelar

Underhåll

Daily
- Visual check whether unit or parts are damaged
- Check whether power cable is damaged
- Check if the riving knife is installed and raised enough.

Annually
- Deep cleaning of the machine, adjusting of the top plates

Logg

Länkar

Instruktionsvideo för hur man använder en bordssåg.

My Top 4 Table Saw Jigs & Accessories: How to Make Them - Pask Makes

Plans for pushsticks

Manual

@@ Rad 1: / Rad 1: @@
+{|
+|- style="color: black; background: #ffc9c9; border: 1px solid #d42b2b; padding: 10px; display: block;"
+|You must complete the [https://medlem.makerspace.se/member/quiz/13 online course] before using this machine
+|}
+==Introduction video==
+<youtube>rrHbCZj1h9U</youtube>
+==Generell information==
 {| style="clear: right; float: right; width: 20em; padding: 0.3em; margin: 0.5em 0 0.5em 1em; border: 1px solid #A3B1BF; background: #f5faff; text-align: left; font-size: 100%; line-height: 1.5em;"
 |-
@@ Rad 18: / Rad 28: @@
 <br />
-==Generell information==
 Bordssåg, Hammer K3 Winner. En stor bordssåg med gjutjärnsbord.
@@ Rad 26: / Rad 35: @@
 *'''Wear safety glasses and turn on the dust extractor'''
 *'''The Riving Knife is the most important safety feature and may not be removed'''
+*'''Do not use any blades not provided by the Makerspace. The saw has special holes to accomodate the motor break.'''
+*'''Do not use Dado-stacks (https://en.wikipedia.org/wiki/Dado_set<nowiki/>)'''
+*'''Never cut stock free hand'''
 *Be certain that the blade is sharp
-*Set the blade so that it extends no more that 5 mm above the stock to be cut
+*Set the blade so that it extends no more than 10 mm above the stock to be cut
 *Stand to one side of the operation blade, do not reach across it
 *Make sure that the stock is fully past the blade before turning the saw off
 *Keep hands at least 15 cm from the blade. Use push sticks when cutting closer
 *Rough stock must be surfaced and at least one side jointed before being cut
-*'''Never cut stock free hand'''
 *Use only new stock that is free of knots, splits and warp
 *Use a push stick to push small scrap away
-*Cross cutting on the table saw is dangerous. 30 cm cross cuts or under should be made on the BOSCH sliding compound miter saw
+*Cross cutting on the table saw is dangerous. 30 cm cross-cuts or under should be made on the BOSCH sliding compound miter saw
 *As you complete your work, turn off the saw and remain until the blade has stopped
 *Clear the saw of dust and waste. Return the saw blade to zero settings. Sweep the work area!
@@ Rad 117: / Rad 128: @@
 [https://paskmakes.com/product/pushstick-template/ Plans for pushsticks]
+[https://www.felder-group.com/WEB/shop/00_Dokumente/503-10103/503010-902_02_1709_HA_BA_K3_basic_winner_ENG_Lo.pdf Manual]
 [[Kategori:Trärummet]]
 [[Kategori:Trä]]
+[[Kategori:Obligatorisk Introkurs]]