Nuvarande version från 13 augusti 2024 kl. 07.40

Nostalgi

Denna sida är inte längre aktuell och sparas främst av nostalgiska skäl.

Maskinen såldes 2024 efter att en ersättare skaffats till det nya trärummet.

Snabbfakta Triton TRA001

Modell: Triton TRA001

Bokningsbar: Nej

Kostnad att använda: Gratis

Power: 2400W

Generell information

Säkerhetsinformation

Handhavande av maskinen

Manual

Description on the Triton website.

Material

For wood and some plastics only.

Do not ever use metal, even as a template.

Usage instructions

Make sure to attach the dust extraction system before using the router.

To raise and lower the bit, always use the big round knob on the router body.

Use the crank above the table only for fine adjustment! It fits in a hole in the table, and reaches to a ball head with a nail through it on the router.

Changing the bit

Unplug the machine. First, flip the switch off. Even with the machine unplugged, it’s necessary to disengage a safety mechanism. You need to push the power switch cover fully open, flip the switch and let the cover close completely.

Then, remove the red protective plate, unlocking it with the grey plastic tool.

Then, using the lifting knob, raise the bit to its highest position. Turning the chuck, you should hear a click when the spindle lock engages.

Once in this position, unlock the bit using the black flat wrench. If the new bit has a shank of a different size, unscrew the chuck completely and replace it with one the proper size.

Place the new bit, tighten it with the wrench, lower it, and place back the red protective plate (using the smallest hole that would fit over the bit).

Put away the tools, flip the switch back on, and you’re good to go!

Power on and off

There are two power switches for the router; one on the front of the router table and one on the right side of the router itself. The switch on the router is lit red when the table switch is turned on. Slide the plastic safety cover back and push the switch to start the router.

Förbrukningsmaterial

Underhåll och reservdelar

Underhåll

Daily

Monthly

Reservdelar

We do not have spare parts for this machine.

Logg

Länkar

Ägare

Maskinen inköpt av Makerspace

Gallery

@@ Rad 1: / Rad 1: @@
+{{Museum}}
+Maskinen såldes 2024 efter att en ersättare skaffats till det nya trärummet.
 {| style="clear: right; float: right; width: 20em; padding: 0.3em; margin: 0.5em 0 0.5em 1em; border: 1px solid #A3B1BF; background: #f5faff; text-align: left; font-size: 100%; line-height: 1.5em;"
 |-
-| align="center" |'''Snabbfakta Bosch GCM8 SJL'''
+| align="center" |'''Snabbfakta Triton TRA001'''
 |-
-|[[Fil:Bosch_GCM8_SJL.jpg|200px|center]]
+|[[Fil:Router Triton TRA001.jpg|centrerad|ramlös|228x228px]]
 |-
-| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Modell:''' ''Bosch GCM8 SJL''
+| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Modell:''' Triton TRA001
 |-
 | style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Bokningsbar:''' Nej
 |-
 | style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Kostnad att använda:''' Gratis
-|- |-
-| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Info 1:''' Kap- och gersåg
-|-
-| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Arbetsyta:''' 70 x 312 mm 52°-60°
-|-
-| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Obelastad hastighet:''' 5500RPM
-|-
-| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Klingdiameter:''' 216 mm
 |-
-| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Klinghåls-Ø:''' 30 mm
+| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Power:''' 2400W
-|-
-| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Märkeffekt:''' 1600W
 |-
-|}<br />
+|}
+==Generell information==
+==Säkerhetsinformation==
-==Generell information==
+==Handhavande av maskinen==
-Sågen kan vinklas 52° Vänster till 60° Höger i förhållande till anhållet i bakkant (geringsvinkel)
+===Manual===
+[http://www.tritontools.com/en-GB/Product/Power%20Tools/Routers/TRA001 Description on the Triton website].
-Sågen kan vinklas 47° Vänster till 2° Höger i förhållande till bordet (snedkapningsvinkel)
+===Material===
+For wood and some plastics only.
+Do not ever use metal, even as a template.
-This saw can be used to cut relatively large pieces of wood and is ideal to make cross-cuts. It is set for square, miter and bevel cuts, or a combination of miter and bevel cuts (compound cut).
+===Usage instructions===
+Make sure to attach the dust extraction system before using the router.
-The saw is attached to the table with 4 screws and some angle combinations are unavailable due to the present configuration.
+To raise and lower the bit, always use the big round knob on the router body.
-It is possible to unscrew the saw and move it to perform special cuts or to cut longer pieces. The saw must be set back to it's initial position.
+'''Use the crank above the table only for fine adjustment!''' It fits in a hole in the table, and reaches to a ball head with a nail through it on the router.
+[[Fil:Router crank.jpg|ramlös|133x133px]]
-This saw can be use to perform non-through cuts (Dados, Grooves & Rabbets) using the depth stop. For such operation, it's usually required to install a sacrificial fence (see pictures in the galerie)
+===Changing the bit===
-==Säkerhetsinformation==
+[[Fil:Router-wrench.jpg|alt=|höger|ramlös]]
+'''Unplug the machine.''' First, flip the switch off. Even with the machine unplugged, it’s necessary to disengage a safety mechanism. You need to push the power switch cover fully open, flip the switch and let the cover close completely.
-*Keep hands at least 15 cm from the blade
+Then, remove the red protective plate, unlocking it with the grey plastic tool.
-*Wear safety glasses and hearing protection
-*Keep the blade guard in position at all times
-*Hold stock firmly on the table and against the fence
-*After making the cut but before raising the saw make sure that the blade has come to a complete stop.
-*When making multiple cuts of various angles do not move hands under the blade whether it is moving or not
-*Sweep the workstation and the floor. All scrap goes in the scrap bin.
-==Handhavande av maskinen==
+Then, using the lifting knob, raise the bit to its highest position. Turning the chuck, you should hear a click when the spindle lock engages.
-===Manual===
-[https://www.bosch-professional.com/binary/ocsmedia/optimized/full/o290859v21_160992A4D3_201808.pdf Manual på Boschs hemsida]
+Once in this position, unlock the bit using the black flat wrench. If the new bit has a shank of a different size, unscrew the chuck completely and replace it with one the proper size.
-===Material===
+Place the new bit, tighten it with the wrench, lower it, and place back the red protective plate (using the smallest hole that would fit over the bit).
-Endast för trä!
-Some plastics can be cut using this saw, but you need to use your own dedicated blade. Always disconnect the power before changing the blade and make sure it's properly centered before starting the saw.
+Put away the tools, flip the switch back on, and you’re good to go!
-===Användarinstruktioner===
-Se till att koppla in dammsugare innan du använder den!
-'''''Skriv något om hur man ställer de olika vinklarna'''''
+==Power on and off==
+There are two power switches for the router; one on the front of the router table and one on the right side of the router itself. The switch on the router is lit red when the table switch is turned on. Slide the plastic safety cover back and push the switch to start the router.
 ==Förbrukningsmaterial==
-We currently have XX spare blades for the miter saw. These blade can be resharpened, do not throw them away, instead label them as "DULL".
-The blades provided by the makerspace are for general purpose and designed for cross-cutting and have about XX teeth.
-You can buy and install your own blade for some specific projects (cutting plastics, Flat kerf blades for joinery, etc) but you must install back the original blade when you are done.
-Klingdiameter: 216 mm
-Klinghåls-Ø: 30 mm
 ==Underhåll och reservdelar==
@@ Rad 80: / Rad 62: @@
 *Daily
-**Visual check whether unit or parts are damaged
-**Check whether power cable is damaged
-**Vacuum and clean the saw and the dust collection box. Throw away scrap wood.
 *Monthly
-**Check the blade sharpness. Change blade if necessary.
-**Clean the laser plastic cover and remove gunk and dust on the saw.
 ===Reservdelar===
@@ Rad 94: / Rad 71: @@
 ==Logg==
-*2020-02-XX: Miter saw station build next to the dust collector.
-*2019-10-05: Inköpt
 *
 ==Länkar==
-https://www.bosch-professional.com/se/sv/products/gcm-8-sjl-0601B19100
-[https://www.youtube.com/watch?v=1HI_1bj4J1U 8 Miter Saw Pro Tips & Tricks - Steve Ramsey - Woodworking for Mere Mortals]
 ==Ägare==
-Maskinen inköpt av Makerspace 2019-08-05
+Maskinen inköpt av Makerspace
 ==Gallery==
-<gallery>
-Fil:MiterSaw.jpg|Cross-cutting large solid planks
-</gallery>