Spånsug, Felder RL 125: Skillnad mellan sidversioner
Cloraux (diskussion | bidrag) |
Cloraux (diskussion | bidrag) |
||
| Rad 6: | Rad 6: | ||
The vacuum should be used at anytime with the following machines: | The vacuum should be used at anytime with the following machines: | ||
* Table saw, table router and planer with the flexible hose. Use as well to clean around the miter saw and the lathe. | |||
* Band saw (one dedicated flexible hose) | |||
* Miter saw (two dedicated pipes) | |||
In a near futur, the belt sander and drill press will have a dedicated hose too. | In a near futur, the belt sander and drill press will have a dedicated hose too. | ||
| Rad 20: | Rad 18: | ||
Not much risks of injuring yourself, but a few things to keep in mind to keep the machine running safely: | Not much risks of injuring yourself, but a few things to keep in mind to keep the machine running safely: | ||
* Do not cut or sand any wet wood as you could clog the filter (which is an expensive spare part) | |||
* Check the level of dust in the bag and change the bag when reaching the maximum level. | |||
* On the side of the machine, there is a handle that you can pull a few times to clean the filter, do not perform this when the machine is running. | |||
* Do not obstruct the air output. | |||
==Handhavande av maskinen== | ==Handhavande av maskinen== | ||
| Rad 44: | Rad 39: | ||
==Reservdelar== | ==Reservdelar== | ||
''Har vi reservdelar på plats?'' | ''Har vi reservdelar på plats?'' | ||
== Maintenance == | |||
=== Daily === | |||
* Visual check whether unit or parts are damaged | |||
* Check whether power cable is damaged | |||
* Check whether dust bags are inserted and check if not full | |||
=== Weekly === | |||
* Machine powered off, pull the filter cleaning handle 4-5 times. This has to be done before every bag replacement. | |||
=== Monthly === | |||
* Visual check for leaks around the filter (dust ejected from the unit cover) | |||
* Check whether the minimum exhaust volume control is functioning correctly | |||
=== Annually === | |||
* Visual check whether dust has collected in fan housing, remove if necessary | |||
* Check whether the seal between dust collector and unit is broken, replace if needed | |||
# | # | ||
Versionen från 23 februari 2020 kl. 18.17
Generell information
The Felder RL 125 is a powerfull chip extractor connected to most of the machines in the woodshop. A sound absorber was added on top of the machine to keep the noise level acceptable. A combination of 100mm fixed pipes and flexible hoses with doors are used to direct the suction to the desired machine.
To use the vacuum, start the machine by turning the red knob and open the desired door connecting to the machine you are using. Check before starting it that all the other doors are closed in order to get the most flow. In a near futur, the vacuum will turn ON and OFF automatically when opening/closing the doors.
The vacuum should be used at anytime with the following machines:
- Table saw, table router and planer with the flexible hose. Use as well to clean around the miter saw and the lathe.
- Band saw (one dedicated flexible hose)
- Miter saw (two dedicated pipes)
In a near futur, the belt sander and drill press will have a dedicated hose too.
Near the belt sander, a pipe goes all the way to the floor and make the floor cleaning really easy.
Säkerhetsinformation
Saker man bör tänka på när man använder maskinen för att inte skada sig, andra, eller maskinen
Not much risks of injuring yourself, but a few things to keep in mind to keep the machine running safely:
- Do not cut or sand any wet wood as you could clog the filter (which is an expensive spare part)
- Check the level of dust in the bag and change the bag when reaching the maximum level.
- On the side of the machine, there is a handle that you can pull a few times to clean the filter, do not perform this when the machine is running.
- Do not obstruct the air output.
Handhavande av maskinen
Manual
Material
Endast för trä!
Användarinstruktioner
Se till att koppla in dammsugare innan du använder den!
Skriv något om hur man ställer de olika vinklarna
Förbrukningsmaterial
The dedicated 200l bags are in a box under the workbench
Reservdelar
Har vi reservdelar på plats?
Maintenance
Daily
- Visual check whether unit or parts are damaged
- Check whether power cable is damaged
- Check whether dust bags are inserted and check if not full
Weekly
- Machine powered off, pull the filter cleaning handle 4-5 times. This has to be done before every bag replacement.
Monthly
- Visual check for leaks around the filter (dust ejected from the unit cover)
- Check whether the minimum exhaust volume control is functioning correctly
Annually
- Visual check whether dust has collected in fan housing, remove if necessary
- Check whether the seal between dust collector and unit is broken, replace if needed
Logg
- 2020-02-XX: Sound absorber added
- 2019-12-XX: Inköpt
Länkar
Ägare
Maskinen inköpt av Makerspace 2019-12-XX
Gallery
-
Switch knob and handle for cleaning the filter
-
Do not cover the hole when replacing the bag
-
Dust collection for the bandsaw
-
Floor swiping
-
Connection to table saw and table router
-
Dust collection for the miter saw
