Bordssåg, Hammer K3 Winner: Skillnad mellan sidversioner
(Skapade sidan med '{| style="clear: right; float: right; width: 20em; padding: 0.3em; margin: 0.5em 0 0.5em 1em; border: 1px solid #A3B1BF; background: #f5faff; text-align: left; font-size: 100%; line-height: 1.5em;" |- | align="center" |'''Snabbfakta Bordssåg, Hammer K3 Winner''' |- | style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Användning:''' Kräver kurs |- | style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Modell:''' Hammer K3 Winner |- | s...') |
Ingen redigeringssammanfattning |
||
Rad 26: | Rad 26: | ||
*'''Wear safety glasses and turn on the dust extractor''' | *'''Wear safety glasses and turn on the dust extractor''' | ||
*'''The Riving Knife is the most important safety feature and may not be removed''' | *'''The Riving Knife is the most important safety feature and may not be removed''' | ||
*'''Do not use any blades not provided by the Makerspace. The saw has special holes to accomodate the motor break.''' | |||
*'''Do not use Dado-stacks (https://en.wikipedia.org/wiki/Dado_set<nowiki/>)''' | |||
*'''Never cut stock free hand''' | |||
*Be certain that the blade is sharp | *Be certain that the blade is sharp | ||
*Set the blade so that it extends no more that 5 mm above the stock to be cut | *Set the blade so that it extends no more that 5 mm above the stock to be cut | ||
Rad 32: | Rad 35: | ||
*Keep hands at least 15 cm from the blade. Use push sticks when cutting closer | *Keep hands at least 15 cm from the blade. Use push sticks when cutting closer | ||
*Rough stock must be surfaced and at least one side jointed before being cut | *Rough stock must be surfaced and at least one side jointed before being cut | ||
*Use only new stock that is free of knots, splits and warp | *Use only new stock that is free of knots, splits and warp | ||
*Use a push stick to push small scrap away | *Use a push stick to push small scrap away |
Versionen från 10 juni 2024 kl. 15.56
Snabbfakta Bordssåg, Hammer K3 Winner |
Användning: Kräver kurs |
Modell: Hammer K3 Winner |
Bokning: Först till kvarn |
Kostnad: Fri |
Loggning: Inget |
Plats: Trärummet |
Generell information
Bordssåg, Hammer K3 Winner. En stor bordssåg med gjutjärnsbord.
Säkerhetsinformation
- Wear safety glasses and turn on the dust extractor
- The Riving Knife is the most important safety feature and may not be removed
- Do not use any blades not provided by the Makerspace. The saw has special holes to accomodate the motor break.
- Do not use Dado-stacks (https://en.wikipedia.org/wiki/Dado_set)
- Never cut stock free hand
- Be certain that the blade is sharp
- Set the blade so that it extends no more that 5 mm above the stock to be cut
- Stand to one side of the operation blade, do not reach across it
- Make sure that the stock is fully past the blade before turning the saw off
- Keep hands at least 15 cm from the blade. Use push sticks when cutting closer
- Rough stock must be surfaced and at least one side jointed before being cut
- Use only new stock that is free of knots, splits and warp
- Use a push stick to push small scrap away
- Cross cutting on the table saw is dangerous. 30 cm cross cuts or under should be made on the BOSCH sliding compound miter saw
- As you complete your work, turn off the saw and remain until the blade has stopped
- Clear the saw of dust and waste. Return the saw blade to zero settings. Sweep the work area!
Handhavande av maskinen
Material
Material | Godkänd | Kommentar |
---|---|---|
Massivt trä | Ja | Om du kan garantera att materialet inte innehåller spikar eller skruvar |
Spånskiva | Ja | |
MDF | Ja | |
Laminatgolv | Nej | Det räcker med att du sågar 20cm i materialet för att göra klingan obrukbar. Riskerar att förstöra sågen. |
Plywood | Ja | |
Laminerade skivor (MDF, Spånskiva osv.) | Ja | Sliter mycket på klingan och för bra resultat behövs oftast en klinga med många tänder och rätt vinkel på tänderna. |
Tryckimpregnerat/Pressure treated wood | Nej | Dust is not safe in our closed environment. |
Metall | Nej | All form av metall är helt förbjuden. Klingan får inte bytas till metallklinga. |
Stone (lightweight chalk, limestone, ...) | Nej | Inga stenlika material tillåts då de förstör klingan och det vassa dammet förstör maskinen. |
Användarinstruktioner
Se till att slå på spånsugen innan du använder den!
Förbrukningsmaterial
We have some spare blades. When a blade does not cut properly, change the blade and label it "Dull" and store it until we have enough of them to bring to resharpening.
Underhåll och reservdelar
Underhåll
- Daily
- Visual check whether unit or parts are damaged
- Check whether power cable is damaged
- Check if the riving knife is installed and raised enough.
- Annually
- Deep cleaning of the machine, adjusting of the top plates
Logg
Länkar
Instruktionsvideo för hur man använder en bordssåg.
My Top 4 Table Saw Jigs & Accessories: How to Make Them - Pask Makes