Skillnad mellan versioner av "Jigs for woodworking"

Från Stockholm Makerspace Wiki
Hoppa till navigering Hoppa till sök
Rad 11: Rad 11:
 
Ensure that the blade is at 90° with the table before using the sled.
 
Ensure that the blade is at 90° with the table before using the sled.
 
===Angle cuts===
 
===Angle cuts===
To perform any angle cut from 89° to 45°, you need to move the sled to the left side of the blade.
+
To perform any angle cut from 89° to 45°, you need to move the sled to the left side of the blade. It is recommended to use a sacrificial fence to avoid tear out.
 +
 
 +
=== Repetitive cuts ===
 +
Woodworking projects often requires multiple identical pieces, measuring and cutting each parts separately will be inaccurate.
 +
 
 +
Instead use a stop block (fixed to the fence with a clamp), or use the dedicated stop mechanism (under construction). Push each board against the block, make a pass through the wood, then set it aside and grab the next piece of stock.
 +
 
 +
For some longer parts, you may use the table saw fence as a reference. Always use a piece of wood between that part that you cut and the fence. Set your part against the piece of wood on the fence, secure your part firmly, remove the small piece of wood and do the cut. Never perform a cut using a non-moving stop block, as you risk squeezing the piece and have it launched into your face.
 +
 
 
==Miter Sled Attachment==
 
==Miter Sled Attachment==
 
==Thin Strip jig==
 
==Thin Strip jig==

Versionen från 9 juni 2020 kl. 08.10

This page list the different jigs that were built for the woodshop. You will find explanation on how to use them properly.

Making these jigs required a considerable amount of time and some money. They were built with extreme care and precision. Please respect that and take care of them.

Always ensure that the blade is perfectly vertical before using any of these jigs.

Crosscut sled

A sled is a movable contraption that slides in the table saw's gauge slots. The workpiece then rests against a wooden fence at the front of the sled, a setup that keeps the work from slipping and ensures a clean, perfectly square cut every time.

Basic crosscuts and safety

With the saw off, set the blade height to cut no higher than 1/8 in. above the wood. Pull the sled back, lay your workpiece against the fence and line up the blade with your cutting mark. Turn the saw on, hold the wood against the fence and slowly push the workpiece through the saw. After the cut is completed, slightly separate the two halves from the blade and shut off the saw. Let the blade coast to a complete stop before you remove the wood.

Ensure that the blade is at 90° with the table before using the sled.

Angle cuts

To perform any angle cut from 89° to 45°, you need to move the sled to the left side of the blade. It is recommended to use a sacrificial fence to avoid tear out.

Repetitive cuts

Woodworking projects often requires multiple identical pieces, measuring and cutting each parts separately will be inaccurate.

Instead use a stop block (fixed to the fence with a clamp), or use the dedicated stop mechanism (under construction). Push each board against the block, make a pass through the wood, then set it aside and grab the next piece of stock.

For some longer parts, you may use the table saw fence as a reference. Always use a piece of wood between that part that you cut and the fence. Set your part against the piece of wood on the fence, secure your part firmly, remove the small piece of wood and do the cut. Never perform a cut using a non-moving stop block, as you risk squeezing the piece and have it launched into your face.

Miter Sled Attachment

Thin Strip jig

Currently under construction

Spline jig

Currently under construction. Almost done.

Tapering jig

Currently under construction

Fingers box joint jig

Currently under construction. Almost done.