166
redigeringar
Plan- och rikthyvel, Scheppach HMC 3200: Skillnad mellan sidversioner
Plan- och rikthyvel, Scheppach HMC 3200 (visa wikitext)
Versionen från 25 februari 2020 kl. 23.29
, 25 februari 2020→Generell information
Cloraux (diskussion | bidrag) Ingen redigeringssammanfattning |
Cloraux (diskussion | bidrag) |
||
| Rad 23: | Rad 23: | ||
==Generell information== | ==Generell information== | ||
<br /> | |||
==Säkerhetsinformation== | ==Säkerhetsinformation== | ||
| Rad 42: | Rad 30: | ||
*Check planer table before turning it on, a tool might have slipped under the cutter head | *Check planer table before turning it on, a tool might have slipped under the cutter head | ||
*Stock must be at least 30 cm long. Minimum 6 mm thick for jointer, 4 mm for planning | *Stock must be at least 30 cm long. Minimum 6 mm thick for jointer, 4 mm for planning | ||
*Blades must be sharp. Dull blades will vibrate the stock and may cause a kickback. | *Blades must be sharp. Dull blades will vibrate the stock and may cause a kickback. | ||
*Clean tool and work area when done | *Clean tool and work area when done | ||
*Feed the work so that the knives will cut “with the grain”. Use only stock that is free of knots and splits. Do not plane end grain | *Feed the work so that the knives will cut “with the grain”. Use only stock that is free of knots and splits. Do not plane end grain | ||
*Use a push block when planing a flat surface. Never apply pressure directly over the knives with your hand. | *Use a push block when planing a flat surface. Never apply pressure directly over the knives with your hand. | ||
*Do not plane the maximum amount off of stock when planing. Two passes through the planer can be better than one. | *Do not plane the maximum amount off of stock when planing. Two passes through the planer can be better than one. | ||
*When planning thin pieces of wood, be sure to stand to one side in case the wood breaks and kicks back. | *When planning thin pieces of wood, be sure to stand to one side in case the wood breaks and kicks back. | ||
*Support the work properly at the in feed and at the out feed. | *Support the work properly at the in feed and at the out feed. | ||
| Rad 55: | Rad 42: | ||
===Manual=== | ===Manual=== | ||
[ | Sprängskiss: [[:Fil:Scheppach hmc 3200 planing combi.pdf]] | ||
===Material=== | ===Material=== | ||
Endast för trä! | Endast för trä! Do to use wet or green wood. Wait 24 hours before planing glued wood pieces. | ||
Use only clean (without nails, screws or sand particles) wood. No other material allowed. | |||
===Användarinstruktioner=== | ===Användarinstruktioner=== | ||
Se till att koppla in dammsugare innan du använder den! | Se till att koppla in dammsugare innan du använder den! | ||
| Rad 67: | Rad 54: | ||
==Förbrukningsmaterial== | ==Förbrukningsmaterial== | ||
We currently have | We currently have 3 sets of blades. Label and store the dull blades. When two sets are dull, send them to resharpening. | ||
==Underhåll och reservdelar== | ==Underhåll och reservdelar== | ||
| Rad 84: | Rad 63: | ||
**Visual check whether unit or parts are damaged | **Visual check whether unit or parts are damaged | ||
**Check whether power cable is damaged | **Check whether power cable is damaged | ||
** | **Check if there is any parts loose around the blades before plugging and running it. | ||
*Monthly | *Monthly | ||
**Check the blade sharpness. Change blade if necessary. | **Check the blade sharpness. Change blade if necessary. | ||
** | *Annually | ||
**Remove the front cover to clean and grease the transmission chain and clean the clutch plates. | |||
*TODO | |||
**Built a side fence for the jointer [[:Fil:Rikthyvel.pdf]] | |||
===Reservdelar=== | ===Reservdelar=== | ||
| Rad 111: | Rad 93: | ||
==Gallery== | ==Gallery== | ||
Ritningsförslag på rikthyvel: [[Fil:Rikthyvel.pdf|miniatyr]] | Ritningsförslag på rikthyvel:[[Fil:Rikthyvel.pdf|miniatyr]] | ||
Sprängskiss: [[Fil:Scheppach_hmc_3200_planing_combi.pdf]] | Sprängskiss: [[Fil:Scheppach_hmc_3200_planing_combi.pdf]] | ||