166
redigeringar
Bordssåg, Meec MJ2325B: Skillnad mellan sidversioner
ingen redigeringssammanfattning
Cloraux (diskussion | bidrag) (→Logg) |
Cloraux (diskussion | bidrag) Ingen redigeringssammanfattning |
||
| Rad 1: | Rad 1: | ||
{| style="clear: right; float: right; width: 20em; padding: 0.3em; margin: 0.5em 0 0.5em 1em; border: 1px solid #A3B1BF; background: #f5faff; text-align: left; font-size: 100%; line-height: 1.5em;" | |||
|- | |||
| align="center" |'''Snabbfakta Scheppach EMC 3200''' | |||
|- | |||
|[[Fil:Scheppach_hmc_3200.jpg|200px|center]] | |||
|- | |||
| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Modell:''' ''Scheppach HMC 3200'' | |||
|- | |||
| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Bokningsbar:''' Nej | |||
|- | |||
| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Kostnad att använda:''' Gratis | |||
|- |- | |||
| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Info 1:''' Kap- och gersåg | |||
|- | |||
| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Arbetsyta:''' 32 cm | |||
|- | |||
| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Obelastad hastighet:''' - RPM | |||
|- | |||
| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Märkeffekt:''' - W | |||
|- | |||
|}<br /> | |||
==Generell information== | |||
<br /> | |||
==Säkerhetsinformation== | |||
*Wear safety glasses, keep hands at least 15 cm from the cutterhead | |||
*Make adjustments with the machine powered off | |||
*Check planer table before turning it on, a tool might have slipped under the cutter head | |||
*Stock must be at least 30 cm long. Minimum 6 mm thick for jointer, 4 mm for planning | |||
*Blades must be sharp. Dull blades will vibrate the stock and may cause a kickback. | |||
*Clean tool and work area when done | |||
*Feed the work so that the knives will cut “with the grain”. Use only stock that is free of knots and splits. Do not plane end grain | |||
*Use a push block when planing a flat surface. Never apply pressure directly over the knives with your hand. | |||
*Do not plane the maximum amount off of stock when planing. Two passes through the planer can be better than one. | |||
*When planning thin pieces of wood, be sure to stand to one side in case the wood breaks and kicks back. | |||
*Support the work properly at the in feed and at the out feed. | |||
==Handhavande av maskinen== | |||
===Manual=== | |||
Sprängskiss: [[:Fil:Scheppach hmc 3200 planing combi.pdf]] | |||
===Material=== | |||
Endast för trä! Do to use wet or green wood. Wait 24 hours before planing glued wood pieces or pieces with epoxy. | |||
Use only clean (without nails, screws or sand particles) wood. No other material allowed. | |||
===Användarinstruktioner=== | |||
Se till att koppla in dammsugare innan du använder den! | |||
'''''Skriv något om hur man ställer de olika vinklarna''''' | |||
==Förbrukningsmaterial== | |||
We currently have 3 sets of blades. Label and store the dull blades. When two sets are dull, send them to resharpening. | |||
==Underhåll och reservdelar== | |||
===Underhåll=== | |||
*Daily | |||
**Visual check whether unit or parts are damaged | |||
**Check whether power cable is damaged | |||
**Check if there is any parts loose around the blades before plugging and running it. | |||
*Monthly | |||
**Check the blade sharpness. Change blade if necessary. | |||
*Annually | |||
**Remove the front cover to clean and grease the transmission chain and clean the clutch plates. | |||
*TODO | |||
**Built a side fence for the jointer [[:Fil:Rikthyvel.pdf]] | |||
===Reservdelar=== | |||
We do not have spare parts for this machine. | |||
# | |||
==Logg== | |||
*2020-01-XX: dust collector built for the planer | |||
*20XX: Inköpt | |||
* | |||
==Länkar== | |||
[https://www.youtube.com/watch?v=YbvPVz9NDxk Wood Jointer Tips for Setting Up and Using a Jointer - WoodWorkWeb] | |||
==Ägare== | |||
Maskinen inköpt av Makerspace | |||
==Gallery== | |||
%%%%%%%%%%%%% | |||
{| style="clear: right; float: right; width: 20em; padding: 0.3em; margin: 0.5em 0 0.5em 1em; border: 1px solid #A3B1BF; background: #f5faff; text-align: left; font-size: 100%; line-height: 1.5em;" | {| style="clear: right; float: right; width: 20em; padding: 0.3em; margin: 0.5em 0 0.5em 1em; border: 1px solid #A3B1BF; background: #f5faff; text-align: left; font-size: 100%; line-height: 1.5em;" | ||
|- | |- | ||