Träsvarv, Solberga SVT 600: Skillnad mellan sidversioner

VisuellWikitext

Nuvarande version från 1 april 2024 kl. 18.48

Snabbfakta Solberga SVT 600

Modell: Solberga SVT 600

Bokningsbar: Nej

Kostnad att använda: Gratis

Arbetsyta:

Obelastad hastighet: 390-2600 RPM

Märkeffekt: -

Generell information

This lathe has an electric motor with two speeds. A lever allow to adjust the speed from 390 to 2600 RPM with the combination of the two speeds switch.

There is an emergency switch in the front panel.

Säkerhetsinformation

Before starting the machine, be sure that spindle work has the cup center properly embedded, tail stock and tool rest are securely clamped and there is proper clearance for the rotating stock

Before starting the machine for faceplate work, disengage the spindle lock and check to see that the faceplate is tight against the spindle shoulder and the tool support has proper clearance
Wear safety glasses and a face shield, especially when roughing out work.
Select turning speed carefully. Large diameters must be turned at the lowest speed. Always use the lowest speed to rough out work.
Wood with knots and splits should not be turned. Glued up stock should cure at least 24 hours.
Keep the tool rest close to the work.
Remove the tool rest for sanding and polishing operations. Use a scraping cut for all face plate work
Remove both the spur and cup centers when they are not in use
When you stop the lathe to check your work also check and lubricate the cup center
Keep the lathe tools sharp; hold them firmly and in the proper position
Keep your sleeves rolled up and other loose clothing away from the moving parts of the lathe and work
Clean up debris and dust

Handhavande av maskinen

Manual

Material

Endast för trä! Wooden with epoxy can also be turned if the epoxy is fully cured.

Användarinstruktioner

Se till att koppla in dammsugare innan du använder den!

To change the chuck: loosen the nut on the left side of the machine, do not unscrew the nut completely but create space between it and the machine. While holding the chuck, give the threaded rod/nut a light blow with a hammer. The chuck should now come loose and you can unscrew the nut on the left side of the machine and pull out the chuck with the thread rod.

Skriv något om hur man ställer de olika vinklarna

Förbrukningsmaterial

Underhåll och reservdelar

Underhåll

Daily
- Visual check whether unit or parts are damaged
- Check whether power cable is damaged
- Vacuum and clean the lathe

Weekly
- Run the lathe and operate it over the full speed range. Dust can over time built up and reduce the range of speed. If it happens, disassemble the speed mechanism and clean it with wire brush and add new grease.
Annually
- Clean and add new grease to the spindle bearings. Clean and grease the speed mechanism.
TODO
- Built some supports on the wall for the tools
- Tailstock alignment

Reservdelar

We have a set of spare V-belts for the lathe.

Upper V-belt: A48

Lower V-belt: A42

Speed lever mechanism needs two 6202 sealed bearings (15*35*11mm)

Logg

2020-02-25: almost running. speed lever under renovation
2019-XX-XX: Inköpt

Länkar

Ägare

Maskinen inköpt av Makerspace 2019-XX-XX

Gallery

@@ Rad 1: / Rad 1: @@
 {| style="clear: right; float: right; width: 20em; padding: 0.3em; margin: 0.5em 0 0.5em 1em; border: 1px solid #A3B1BF; background: #f5faff; text-align: left; font-size: 100%; line-height: 1.5em;"
 |-
-| align="center" |'''Snabbfakta Bosch GCM8 SJL'''
+| align="center" |'''Snabbfakta Solberga SVT 600'''
 |-
-|[[Fil:Bosch_GCM8_SJL.jpg|200px|center]]
+|[[Fil:Woodlathe.jpg|alt=|centrerad|266x266px]]
 |-
-| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Modell:''' ''Bosch GCM8 SJL''
+| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Modell:''' ''Solberga SVT 600''
 |-
 | style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Bokningsbar:''' Nej
 |-
 | style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Kostnad att använda:''' Gratis
-|- |-
-| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Info 1:''' Kap- och gersåg
 |-
-| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Arbetsyta:''' 70 x 312 mm 52°-60°
+| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Arbetsyta:'''
 |-
-| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Obelastad hastighet:''' 5500RPM
+| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Obelastad hastighet:''' 390-2600 RPM
 |-
-| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Klingdiameter:''' 216 mm
+| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Märkeffekt:''' -
-|-
-| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Klinghåls-Ø:''' 30 mm
-|-
-| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Märkeffekt:''' 1600W
 |-
@@ Rad 27: / Rad 21: @@
 ==Generell information==
-Sågen kan vinklas 52° Vänster till 60° Höger i förhållande till anhållet i bakkant (geringsvinkel)
+This lathe has an electric motor with two speeds. A lever allow to adjust the speed from 390 to 2600 RPM with the combination of the two speeds switch.
-Sågen kan vinklas 47° Vänster till 2° Höger i förhållande till bordet (snedkapningsvinkel)
+There is an emergency switch in the front panel. <br />
+==Säkerhetsinformation==
-This saw can be used to cut relatively large pieces of wood and is ideal to make cross-cuts. It is set for square, miter and bevel cuts, or a combination of miter and bevel cuts (compound cut).
+*Before starting the machine, be sure that spindle work has the cup center properly embedded, tail stock and tool rest are securely clamped and there is proper clearance for the rotating stock
-The saw is attached to the table with 4 screws and some angle combinations are unavailable due to the present configuration.
+*Before starting the machine for faceplate work, disengage the spindle lock and check to see that the faceplate is tight against the spindle shoulder and the tool support has proper clearance
+*'''Wear safety glasses and a face shield, especially when roughing out work.'''
-It is possible to unscrew the saw and move it to perform special cuts or to cut longer pieces. The saw must be set back to it's initial position.
+*Select turning speed carefully. Large diameters must be turned at the lowest speed. Always use the lowest speed to rough out work.
+*Wood with knots and splits should not be turned. Glued up stock should cure at least 24 hours.
+*Keep the tool rest close to the work.
-This saw can be use to perform non-through cuts (Dados, Grooves & Rabbets) using the depth stop. For such operation, it's usually required to install a sacrificial fence (see pictures in the galerie)
+*Remove the tool rest for sanding and polishing operations. Use a scraping cut for all face plate work
-==Säkerhetsinformation==
+*Remove both the spur and cup centers when they are not in use
+*When you stop the lathe to check your work also check and lubricate the cup center
-*Keep hands at least 15 cm from the blade
+*Keep the lathe tools sharp; hold them firmly and in the proper position
-*Wear safety glasses and hearing protection
+*Keep your sleeves rolled up and other loose clothing away from the moving parts of the lathe and work
-*Keep the blade guard in position at all times
+*Clean up debris and dust
-*Hold stock firmly on the table and against the fence
-*After making the cut but before raising the saw make sure that the blade has come to a complete stop.
-*When making multiple cuts of various angles do not move hands under the blade whether it is moving or not
-*Sweep the workstation and the floor. All scrap goes in the scrap bin.
 ==Handhavande av maskinen==
 ===Manual===
-[https://www.bosch-professional.com/binary/ocsmedia/optimized/full/o290859v21_160992A4D3_201808.pdf Manual på Boschs hemsida]
+<br />
 ===Material===
-Endast för trä!
+Endast för trä! Wooden with epoxy can also be turned if the epoxy is fully cured.
-Some plastics can be cut using this saw, but you need to use your own dedicated blade. Always disconnect the power before changing the blade and make sure it's properly centered before starting the saw.
 ===Användarinstruktioner===
 Se till att koppla in dammsugare innan du använder den!
+To change the chuck: loosen the nut on the left side of the machine, do not unscrew the nut completely but create space between it and the machine. While holding the chuck, give the threaded rod/nut a light blow with a hammer. The chuck should now come loose and you can unscrew the nut on the left side of the machine and pull out the chuck with the thread rod.
 '''''Skriv något om hur man ställer de olika vinklarna'''''
 ==Förbrukningsmaterial==
-We currently have XX spare blades for the miter saw. These blade can be resharpened, do not throw them away, instead label them as "DULL".
+<br />
-The blades provided by the makerspace are for general purpose and designed for cross-cutting and have about XX teeth.
-You can buy and install your own blade for some specific projects (cutting plastics, Flat kerf blades for joinery, etc) but you must install back the original blade when you are done.
-Klingdiameter: 216 mm
-Klinghåls-Ø: 30 mm
 ==Underhåll och reservdelar==
@@ Rad 82: / Rad 64: @@
 **Visual check whether unit or parts are damaged
 **Check whether power cable is damaged
-**Vacuum and clean the saw and the dust collection box. Throw away scrap wood.
+**Vacuum and clean the lathe
-*Monthly
+*Weekly
-**Check the blade sharpness. Change blade if necessary.
+**Run the lathe and operate it over the full speed range. Dust can over time built up and reduce the range of speed. If it happens, disassemble the speed mechanism and clean it with wire brush and add new grease.
-**Clean the laser plastic cover and remove gunk and dust on the saw.
+*Annually
+**Clean and add new grease to the spindle bearings. Clean and grease the speed mechanism.
+*TODO
+**Built some supports on the wall for the tools
+**Tailstock alignment
 ===Reservdelar===
-We do not have spare parts for this machine.
+We have a set of spare V-belts for the lathe.
+Upper V-belt: A48
+Lower V-belt: A42
+Speed lever mechanism needs two [https://www.kullagret.com/product/6202-2rs-kullager 6202 sealed bearings] (15*35*11mm)
 #
@@ Rad 95: / Rad 87: @@
 ==Logg==
-*2020-02-XX: Miter saw station build next to the dust collector.
+*2020-02-25: almost running. speed lever under renovation
-*2019-10-05: Inköpt
+*2019-XX-XX: Inköpt
 *
 ==Länkar==
-https://www.bosch-professional.com/se/sv/products/gcm-8-sjl-0601B19100
-[https://www.youtube.com/watch?v=1HI_1bj4J1U 8 Miter Saw Pro Tips & Tricks - Steve Ramsey - Woodworking for Mere Mortals]
 ==Ägare==
-Maskinen inköpt av Makerspace 2019-08-05
+Maskinen inköpt av Makerspace 2019-XX-XX
 ==Gallery==
-<gallery>
-Fil:MiterSaw.jpg|Cross-cutting large solid planks
+[[Kategori:Trärummet]]
-</gallery>
+[[Kategori:Trä]]