Bandsåg, EJCA BA45: Skillnad mellan sidversioner

VisuellWikitext

Nuvarande version från 10 september 2024 kl. 18.24

Snabbfakta EJCA BA45

Modell: EJCA BA45

Bokningsbar: Nej

Kostnad att använda: Gratis

Obelastad hastighet: -

Blade length: 3090 mm

Wheels-Ø: 446 x 32 mm

Märkeffekt: 1.0 hk

Generell information

Bandsåg för trä

Gedigen gjutjärnsmaskin tillverkad på 60- till 70-talet.

OBS! Kräver genomgång av kurs före användning! / Requires completion of course before use!

/// VERY IMPORTANT INFORMATION ///

This machine has a wide blade installed. This means it is only for straight cuts (or very wide curves). Use the other bandsaw for curves.

Säkerhetsinformation

Wheel guard doors closed and blade properly adjusted before turning on the machine
Upper guide assembly no more than 1cm above the work
Allow the saw to reach full speed before starting to feed the work
The stock must be held flat on the table
Feed the saw only as fast as the teeth will remove the wood easily
Keep hands at least 10 cm away from the blade
Plan cuts to avoid backing out of curves, whenever possible
Make turns carefully and do not cut radii so small that the blade is twisted then broken
Round stock should not be cut unless mounted firmly in a jig
Do not let small pieces of wood accumulate around the blade
If you hear a clicking noise, turn off the machine at once. This sound indicates a crack in the blade
Turn off the machine as soon as you finish working
Sweep the table and the floor. All scrap in the scrap bin. Lower the upper guide assembly

Handhavande av maskinen

Manual

Instruktionsbok_Ejca_BA40,45,50

Material

Endast för trä! Do not cut wet or green wood. Do not cut freshly glued wood, wait at least 24h before cutting.

Some plastics and foam can be cut using this saw.

Användarinstruktioner

Se till att koppla in dammsugare innan du använder den!

Skriv något om hur man ställer de olika vinklarna

Byta blad på bandsågen

Det är viktigt att du ställer in spänningen på bladet rätt och att guiderna för bladet också är rätt inställda. Här är en bra video som går igenom hur du gör det: https://www.youtube.com/watch?v=bxVyKsbuwZQ.

English: Changing the blade on the bandsaw

It is very important that you adjust the belt tension and the blade guides correctly. Here is a great video that explains exactly how to do this: https://www.youtube.com/watch?v=bxVyKsbuwZQ.

Förbrukningsmaterial

The blades provided by the makerspace, for this saw, are for resawing.

Blade length: 3090 mm

3086mm / 19mm / 4TPI

To order new blades: http://www.bandsagblad.se/

Underhåll och reservdelar

Underhåll

Daily
- Check for the blade alignment, and blade guide alignment (upper and lower guides).
- Adjust the upper blade guide assembly height
- Visual check whether unit or parts are damaged
- Check whether power cable is damaged
- Vacuum and clean the saw.

Monthly
- Check the blade sharpness. Change blade if necessary.
- Check the lower blade garde wooden blocs and replace them is necessary.
- Check and clean the inside of the saw and inspect the tires
Annually
- Grease the lower and upper wheel shafts. After letting the saw run for a few minutes, wipe out the excess of grease.
TODO
- Balance the wheels

Reservdelar

We have the set of spare bearings for the top and the bottom wheels. If they ever need to be replaced.

/// Add link for the new tires ///

Logg

2024-05-XX: Changed to permanently have a wide blade mounted. We now have a different table saw for curves.
2020-03-XX: New urethane tires and upper blade guides
2020-02-XX: 100mm vacuum connector added
2018-XX-XX: Har fått motorskydd, nödstopp samt nya start och stoppknappar
2018-XX-XX: Inköpt

Länkar

Bandsaw Tips and Tricks for Woodworkers - Make Something

The Best Way to Set Up a Bandsaw

Ägare

Maskinen inköpt av Makerspace 2018-XX-XX

Gallery

@@ Rad 1: / Rad 1: @@
 {| style="clear: right; float: right; width: 20em; padding: 0.3em; margin: 0.5em 0 0.5em 1em; border: 1px solid #A3B1BF; background: #f5faff; text-align: left; font-size: 100%; line-height: 1.5em;"
 |-
-| align="center" |'''Snabbfakta Bosch GCM8 SJL'''
+| align="center" |'''Snabbfakta EJCA BA45'''
 |-
-|[[Fil:Bosch_GCM8_SJL.jpg|200px|center]]
+|[[Fil:Bandsåg_Ejca_BA45.jpg|200px|center]]
 |-
-| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Modell:''' ''Bosch GCM8 SJL''
+| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Modell:''' ''EJCA BA45''
 |-
 | style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Bokningsbar:''' Nej
 |-
 | style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Kostnad att använda:''' Gratis
-|- |-
-| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Info 1:''' Kap- och gersåg
 |-
-| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Arbetsyta:''' 70 x 312 mm 52°-60°
+| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Obelastad hastighet:''' -
 |-
-| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Obelastad hastighet:''' 5500RPM
+| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Blade length:''' 3090 mm
 |-
-| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Klingdiameter:''' 216 mm
+| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Wheels-Ø:''' 446 x 32 mm
 |-
-| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Klinghåls-Ø:''' 30 mm
+| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Märkeffekt:''' 1.0 hk
-|-
-| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Märkeffekt:''' 1600W
 |-
@@ Rad 27: / Rad 23: @@
 ==Generell information==
-Sågen kan vinklas 52° Vänster till 60° Höger i förhållande till anhållet i bakkant (geringsvinkel)
+Bandsåg för trä
-Sågen kan vinklas 47° Vänster till 2° Höger i förhållande till bordet (snedkapningsvinkel)
+Gedigen gjutjärnsmaskin tillverkad på 60- till 70-talet.
+OBS! Kräver genomgång av [https://medlem.makerspace.se/member/quiz/5 kurs] före användning! / Requires completion of [https://medlem.makerspace.se/member/quiz/5 course] before use!
-This saw can be used to cut relatively large pieces of wood and is ideal to make cross-cuts. It is set for square, miter and bevel cuts, or a combination of miter and bevel cuts (compound cut).
-The saw is attached to the table with 4 screws and some angle combinations are unavailable due to the present configuration.
+/// VERY IMPORTANT INFORMATION ///
-It is possible to unscrew the saw and move it to perform special cuts or to cut longer pieces. The saw must be set back to it's initial position.
+This machine has a wide blade installed. This means it is only for straight cuts (or very wide curves). Use the other bandsaw for curves.
-This saw can be use to perform non-through cuts (Dados, Grooves & Rabbets) using the depth stop. For such operation, it's usually required to install a sacrificial fence (see pictures in the galerie)
 ==Säkerhetsinformation==
-*Keep hands at least 15 cm from the blade
+*'''Wheel guard doors closed and blade properly adjusted before turning on the machine'''
-*Wear safety glasses and hearing protection
+*Upper guide assembly no more than 1cm above the work
-*Keep the blade guard in position at all times
+*Allow the saw to reach full speed before starting to feed the work
-*Hold stock firmly on the table and against the fence
+*The stock must be held flat on the table
-*After making the cut but before raising the saw make sure that the blade has come to a complete stop.
+*Feed the saw only as fast as the teeth will remove the wood easily
-*When making multiple cuts of various angles do not move hands under the blade whether it is moving or not
+*Keep hands at least 10 cm away from the blade
-*Sweep the workstation and the floor. All scrap goes in the scrap bin.
+*Plan cuts to avoid backing out of curves, whenever possible
+*Make turns carefully and do not cut radii so small that the blade is twisted then broken
+*Round stock should not be cut unless mounted firmly in a jig
+*Do not let small pieces of wood accumulate around the blade
+*If you hear a clicking noise, turn off the machine at once. This sound indicates a crack in the blade
+*Turn off the machine as soon as you finish working
+*Sweep the table and the floor. All scrap in the scrap bin. Lower the upper guide assembly
 ==Handhavande av maskinen==
 ===Manual===
-[https://www.bosch-professional.com/binary/ocsmedia/optimized/full/o290859v21_160992A4D3_201808.pdf Manual på Boschs hemsida]
+[[Media:Instruktionsbok Ejca BA40,45,50.pdf|Instruktionsbok_Ejca_BA40,45,50]]
 ===Material===
-Endast för trä!
+Endast för trä! Do not cut wet or green wood. Do not cut freshly glued wood, wait at least 24h before cutting.
-Some plastics can be cut using this saw, but you need to use your own dedicated blade. Always disconnect the power before changing the blade and make sure it's properly centered before starting the saw.
+Some plastics and foam can be cut using this saw.
 ===Användarinstruktioner===
 Se till att koppla in dammsugare innan du använder den!
 '''''Skriv något om hur man ställer de olika vinklarna'''''
+===Byta blad på bandsågen===
+Det är viktigt att du ställer in spänningen på bladet rätt och att guiderna för bladet också är rätt inställda.
+Här är en bra video som går igenom hur du gör det: https://www.youtube.com/watch?v=bxVyKsbuwZQ.
+====English: Changing the blade on the bandsaw====
+It is very important that you adjust the belt tension and the blade guides correctly.
+Here is a great video that explains exactly how to do this: https://www.youtube.com/watch?v=bxVyKsbuwZQ.
 ==Förbrukningsmaterial==
-We currently have XX spare blades for the miter saw. These blade can be resharpened, do not throw them away, instead label them as "DULL".
+The blades provided by the makerspace, for this saw, are for resawing.
-The blades provided by the makerspace are for general purpose and designed for cross-cutting and have about XX teeth.
+Blade length: 3090 mm
-You can buy and install your own blade for some specific projects (cutting plastics, Flat kerf blades for joinery, etc) but you must install back the original blade when you are done.
+mm / 19mm / 4TPI
-Klingdiameter: 216 mm
-Klinghåls-Ø: 30 mm
+To order new blades: <nowiki>http://www.bandsagblad.se/</nowiki>
 ==Underhåll och reservdelar==
@@ Rad 80: / Rad 86: @@
 *Daily
+**Check for the blade alignment, and blade guide alignment (upper and lower guides).
+**Adjust the upper blade guide assembly height
 **Visual check whether unit or parts are damaged
 **Check whether power cable is damaged
-**Vacuum and clean the saw and the dust collection box. Throw away scrap wood.
+**Vacuum and clean the saw.
 *Monthly
 **Check the blade sharpness. Change blade if necessary.
-**Clean the laser plastic cover and remove gunk and dust on the saw.
+**Check the lower blade garde wooden blocs and replace them is necessary.
+**Check and clean the inside of the saw and inspect the tires
+*Annually
+**Grease the lower and upper wheel shafts. After letting the saw run for a few minutes, wipe out the excess of grease.
+*TODO
+**Balance the wheels
 ===Reservdelar===
-We do not have spare parts for this machine.
+We have the set of spare bearings for the top and the bottom wheels. If they ever need to be replaced.
+/// Add link for the new tires ///
 #
@@ Rad 95: / Rad 110: @@
 ==Logg==
-*2020-02-XX: Miter saw station build next to the dust collector.
+*2024-05-XX: Changed to permanently have a wide blade mounted. We now have a different table saw for curves.
-*2019-10-05: Inköpt
+*2020-03-XX: New urethane tires and upper blade guides
+*2020-02-XX: 100mm vacuum connector added
+*2018-XX-XX: Har fått motorskydd, nödstopp samt nya start och stoppknappar
+*2018-XX-XX: Inköpt
 *
 ==Länkar==
-https://www.bosch-professional.com/se/sv/products/gcm-8-sjl-0601B19100
-[https://www.youtube.com/watch?v=1HI_1bj4J1U 8 Miter Saw Pro Tips & Tricks - Steve Ramsey - Woodworking for Mere Mortals]
+[https://www.youtube.com/watch?v=QbJBQYDrF5M Bandsaw Tips and Tricks for Woodworkers - Make Something]
+[https://www.youtube.com/watch?v=bxVyKsbuwZQ The Best Way to Set Up a Bandsaw]
 ==Ägare==
-Maskinen inköpt av Makerspace 2019-08-05
+Maskinen inköpt av Makerspace 2018-XX-XX
 ==Gallery==
-<gallery>
-Fil:MiterSaw.jpg|Cross-cutting large solid planks
-</gallery>
-[[Fil:Bandsåg_Ejca_BA45.jpg|400px|thumb|left|EJCA BA45]]
-Bandsåg för trä
-Gedigen gjutjärnsmaskin tillverkad på 60- till 70-talet.
-Ägare: Stockholm Makerspace
-Längd på band: 3090mm
-El: 3 fas
-Har fått motorskydd, nödstopp samt nya start och stoppknappar under 2018.
-Manual:
+[[Kategori:Trärummet]]
-[[Media:Instruktionsbok Ejca BA40,45,50.pdf]]
+[[Kategori:Obligatorisk Introkurs]]
+[[Kategori:Trä]]