Träsvarv, Solberga SVT 600: Skillnad mellan sidversioner

VisuellWikitext

Nuvarande version från 14 november 2024 kl. 17.58

Snabbfakta Solberga SVT 600

Modell: Solberga SVT 600

Bokningsbar: Nej

Kostnad att använda: Gratis

Arbetsyta:

Obelastad hastighet: 390-2600 RPM

Märkeffekt: -

Generell information

This lathe has an electric motor with two speeds. A lever allow to adjust the speed from 390 to 2600 RPM with the combination of the two speeds switch.

There is an emergency switch in the front panel.

Säkerhetsinformation

Before starting the machine, be sure that spindle work has the cup center properly embedded, tail stock and tool rest are securely clamped and there is proper clearance for the rotating stock

Before starting the machine for faceplate work, disengage the spindle lock and check to see that the faceplate is tight against the spindle shoulder and the tool support has proper clearance
Wear safety glasses and a face shield, especially when roughing out work.
Select turning speed carefully. Large diameters must be turned at the lowest speed. Always use the lowest speed to rough out work.
Wood with knots and splits should not be turned. Glued up stock should cure at least 24 hours.
Keep the tool rest close to the work.
Remove the tool rest for sanding and polishing operations. Use a scraping cut for all face plate work
Remove both the spur and cup centers when they are not in use
When you stop the lathe to check your work also check and lubricate the cup center
Keep the lathe tools sharp; hold them firmly and in the proper position
Keep your sleeves rolled up and other loose clothing away from the moving parts of the lathe and work
Clean up debris and dust

Handhavande av maskinen

Manual

Material

Endast för trä! Wooden with epoxy can also be turned if the epoxy is fully cured.

Användarinstruktioner

Se till att koppla in dammsugare innan du använder den!

To change the chuck: loosen the nut on the left side of the machine, do not unscrew the nut completely but create space between it and the machine. While holding the chuck, give the threaded rod/nut a light blow with a hammer. The chuck should now come loose and you can unscrew the nut on the left side of the machine and pull out the chuck with the thread rod.

Skriv något om hur man ställer de olika vinklarna

Förbrukningsmaterial

Underhåll och reservdelar

Underhåll

Daily
- Visual check whether unit or parts are damaged
- Check whether power cable is damaged
- Vacuum and clean the lathe

Weekly
- Run the lathe and operate it over the full speed range. Dust can over time built up and reduce the range of speed. If it happens, disassemble the speed mechanism and clean it with wire brush and add new grease.
Annually
- Clean and add new grease to the spindle bearings. Clean and grease the speed mechanism.
TODO
- Built some supports on the wall for the tools
- Tailstock alignment

Reservdelar

We have a set of spare V-belts for the lathe.

Upper V-belt: A48

Lower V-belt: A42

Speed lever mechanism needs two 6202 sealed bearings (15*35*11mm)

Logg

2020-02-25: almost running. speed lever under renovation
2019-XX-XX: Inköpt

Länkar

Ägare

Maskinen inköpt av Makerspace 2019-XX-XX

Gallery

@@ Rad 11: / Rad 11: @@
 | style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Kostnad att använda:''' Gratis
 |-
 | style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Arbetsyta:'''
 |-
 | style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Obelastad hastighet:''' 390-2600 RPM
@@ Rad 21: / Rad 21: @@
 ==Generell information==
-<br />
+This lathe has an electric motor with two speeds. A lever allow to adjust the speed from 390 to 2600 RPM with the combination of the two speeds switch.
+There is an emergency switch in the front panel. <br />
 ==Säkerhetsinformation==
-* Before starting the machine, be sure that spindle work has the cup center properly embedded, tail stock and tool rest are securely clamped and there is proper clearance for the rotating stock
+*Before starting the machine, be sure that spindle work has the cup center properly embedded, tail stock and tool rest are securely clamped and there is proper clearance for the rotating stock
-* Before starting the machine for faceplate work, disengage the spindle lock and check to see that the faceplate is tight against the spindle shoulder and the tool support has proper clearance
+*Before starting the machine for faceplate work, disengage the spindle lock and check to see that the faceplate is tight against the spindle shoulder and the tool support has proper clearance
-* '''Wear safety glasses and a face shield, especially when roughing out work.'''
+*'''Wear safety glasses and a face shield, especially when roughing out work.'''
-* Select turning speed carefully. Large diameters must be turned at the lowest speed. Always use the lowest speed to rough out work.
+*Select turning speed carefully. Large diameters must be turned at the lowest speed. Always use the lowest speed to rough out work.
-* Wood with knots and splits should not be turned. Glued up stock should cure at least 24 hours.
+*Wood with knots and splits should not be turned. Glued up stock should cure at least 24 hours.
-* Keep the tool rest close to the work.
+*Keep the tool rest close to the work.
-* Remove the tool rest for sanding and polishing operations. Use a scraping cut for all face plate work
+*Remove the tool rest for sanding and polishing operations. Use a scraping cut for all face plate work
-* Remove both the spur and cup centers when they are not in use
+*Remove both the spur and cup centers when they are not in use
-* When you stop the lathe to check your work also check and lubricate the cup center
+*When you stop the lathe to check your work also check and lubricate the cup center
-* Keep the lathe tools sharp; hold them firmly and in the proper position
+*Keep the lathe tools sharp; hold them firmly and in the proper position
-* Keep your sleeves rolled up and other loose clothing away from the moving parts of the lathe and work
+*Keep your sleeves rolled up and other loose clothing away from the moving parts of the lathe and work
-* Clean up debris and dust
+*Clean up debris and dust
 ==Handhavande av maskinen==
@@ Rad 47: / Rad 49: @@
 ===Användarinstruktioner===
 Se till att koppla in dammsugare innan du använder den!
+To change the chuck: loosen the nut on the left side of the machine, do not unscrew the nut completely but create space between it and the machine. While holding the chuck, give the threaded rod/nut a light blow with a hammer. The chuck should now come loose and you can unscrew the nut on the left side of the machine and pull out the chuck with the thread rod.
 '''''Skriv något om hur man ställer de olika vinklarna'''''
@@ Rad 67: / Rad 71: @@
 **Clean and add new grease to the spindle bearings. Clean and grease the speed mechanism.
 *TODO
-**Connect the lights on the lathe garde
-**Rebuild the speed mechanism and install the A48 v-belt instead of the A49 currently in.
-**Decide whether we need the engine two speed switch or only the on/off switch.
 **Built some supports on the wall for the tools
+**Tailstock alignment
 ===Reservdelar===
@@ Rad 95: / Rad 97: @@
 ==Gallery==
+[[Kategori:Trärummet]]
+[[Kategori:Trä]]
+[[Kategori:Kunskaps- och säkerhetskrav]]