293
redigeringar
Bordssåg, Hammer K3 Winner: Skillnad mellan sidversioner
→Logg
Ingen redigeringssammanfattning |
Voxel (diskussion | bidrag) (→Logg) |
||
| (6 mellanliggande sidversioner av 4 användare visas inte) | |||
| Rad 1: | Rad 1: | ||
{| | |||
|- style="color: black; background: #ffc9c9; border: 1px solid #d42b2b; padding: 10px; display: block;" | |||
|You must complete the [https://medlem.makerspace.se/member/quiz/13 online course] before using this machine | |||
|} | |||
==Introduction video== | |||
<youtube>rrHbCZj1h9U</youtube> | |||
==Generell information== | |||
{| style="clear: right; float: right; width: 20em; padding: 0.3em; margin: 0.5em 0 0.5em 1em; border: 1px solid #A3B1BF; background: #f5faff; text-align: left; font-size: 100%; line-height: 1.5em;" | {| style="clear: right; float: right; width: 20em; padding: 0.3em; margin: 0.5em 0 0.5em 1em; border: 1px solid #A3B1BF; background: #f5faff; text-align: left; font-size: 100%; line-height: 1.5em;" | ||
|- | |- | ||
| Rad 18: | Rad 28: | ||
<br /> | <br /> | ||
Bordssåg, Hammer K3 Winner. En stor bordssåg med gjutjärnsbord. | Bordssåg, Hammer K3 Winner. En stor bordssåg med gjutjärnsbord. | ||
| Rad 30: | Rad 39: | ||
*'''Never cut stock free hand''' | *'''Never cut stock free hand''' | ||
*Be certain that the blade is sharp | *Be certain that the blade is sharp | ||
*Set the blade so that it extends no more | *Set the blade so that it extends no more than 10 mm above the stock to be cut | ||
*Stand to one side of the operation blade, do not reach across it | *Stand to one side of the operation blade, do not reach across it | ||
*Make sure that the stock is fully past the blade before turning the saw off | *Make sure that the stock is fully past the blade before turning the saw off | ||
| Rad 37: | Rad 46: | ||
*Use only new stock that is free of knots, splits and warp | *Use only new stock that is free of knots, splits and warp | ||
*Use a push stick to push small scrap away | *Use a push stick to push small scrap away | ||
*Cross cutting on the table saw is dangerous. 30 cm cross cuts or under should be made on the BOSCH sliding compound miter saw | *Cross cutting on the table saw is dangerous. 30 cm cross-cuts or under should be made on the BOSCH sliding compound miter saw | ||
*As you complete your work, turn off the saw and remain until the blade has stopped | *As you complete your work, turn off the saw and remain until the blade has stopped | ||
*Clear the saw of dust and waste. Return the saw blade to zero settings. Sweep the work area! | *Clear the saw of dust and waste. Return the saw blade to zero settings. Sweep the work area! | ||
| Rad 110: | Rad 119: | ||
==Logg== | ==Logg== | ||
2025-01-05: | |||
Table saw cleaned throughly, was full of saw dust as the hose and adapter were disconnected. Adapter was broken and a new one is being printed. | |||
Cleaned and lubricated the height spindle. It still feels like it's hard to adjust upward, but not affecting the performance or operation of the machine. | |||
Cleaned and lubricated tilting spindle. There is a clicking sound at around 40 degrees. Unclear what. | |||
Checked the drive and scoring belt. Found OK | |||
The blade is aligned to 90+/-0.1 degrees. Parallel fence is, as far as we could tell, parallel to the blade. The cross-cut fence is, not quite 90 degrees to the blade. Needs to be secured. Slight wobble on the crosscut fence so you have to be careful. | |||
==Länkar== | ==Länkar== | ||
| Rad 119: | Rad 139: | ||
[https://paskmakes.com/product/pushstick-template/ Plans for pushsticks] | [https://paskmakes.com/product/pushstick-template/ Plans for pushsticks] | ||
[https://www.felder-group.com/WEB/shop/00_Dokumente/503-10103/503010-902_02_1709_HA_BA_K3_basic_winner_ENG_Lo.pdf Manual] | |||
[https://www.youtube.com/watch?v=raMZ_fhUklg YT video on how to calibrate the Hammer K3] | |||
[[Kategori:Trärummet]] | [[Kategori:Trärummet]] | ||
[[Kategori:Trä]] | [[Kategori:Trä]] | ||
[[Kategori:Obligatorisk Introkurs]] | |||