Spånsug, Felder RL 125: Skillnad mellan sidversioner
Cloraux (diskussion | bidrag) |
(Mycket) |
||
| (4 mellanliggande sidversioner av 3 användare visas inte) | |||
| Rad 1: | Rad 1: | ||
== | ==General information== | ||
[[Fil:Felder RL 125.jpg|miniatyr]]The [https://www.felder-group.com/en-us/products/dust-extractors-c1963 Felder] RL 125 is a powerfull chip extractor connected to most of the machines in the woodshop. A sound absorber was added on top of the machine to keep the noise level acceptable. A combination of 100mm fixed pipes and flexible hoses with doors are used to direct the suction to the desired machine. | [[Fil:Felder RL 125.jpg|miniatyr]]The [https://www.felder-group.com/en-us/products/dust-extractors-c1963 Felder] RL 125 is a powerfull chip extractor connected to most of the machines in the woodshop. A sound absorber was added on top of the machine to keep the noise level acceptable. A combination of 100mm fixed pipes and flexible hoses with doors are used to direct the suction to the desired machine. | ||
To use the vacuum, start the machine by turning the red knob and open the desired door connecting to the machine you are using. Check before starting | To use the vacuum, start the machine by turning the red knob and open the desired door connecting to the machine you are using. Check before starting that all the other doors are closed in order to get the most flow. | ||
The vacuum should be used at anytime with the following machines: | The vacuum should be used at anytime with the following machines: | ||
*Table saw | *Table saw (dedicated hose) | ||
*Band saw ( | *Table router and planer/jointer use the same hose. You can use it to clean around them as well. | ||
*Miter saw ( | *Band saw (dedicated hose) | ||
*Beltsander ( | *Miter saw (dedicated hose) | ||
*Lathe (one dedicated hose with large funnel | *Beltsander (dedicated hose) | ||
*Lathe (one dedicated hose with large funnel) | |||
It is not required to use the dust collection on the drill press | It is not required to use the dust collection on the drill press. | ||
Regularly check for the level of dust in the bag, and properly replace the plastic bag if needed. See instructions below. | Regularly check for the level of dust in the bag, and properly replace the plastic bag if needed. See instructions below. | ||
== | ==Safety information== | ||
'' | ''Things to consider when using the machine to not hurt the machine, others, and yourself.'' | ||
Not much risks of injuring yourself, but a few things to keep in mind to keep the machine running safely: | Not much risks of injuring yourself, but a few things to keep in mind to keep the machine running safely: | ||
| Rad 24: | Rad 25: | ||
*'''Do not cut or sand any wet wood as you could clog the filter (which is an expensive spare part)''' | *'''Do not cut or sand any wet wood as you could clog the filter (which is an expensive spare part)''' | ||
*'''Check the level of dust in the bag and change the bag when reaching the maximum level.''' | *'''Check the level of dust in the bag and change the bag when reaching the maximum level.''' | ||
*On the side of the machine, there is a handle that you can pull a few times to clean the filter, do not perform this when the machine is running. | *On the left side of the machine, there is a handle that you can pull a few times to clean the filter, do not perform this when the machine is running. | ||
*Do not obstruct the air output. | *Do not obstruct the air output. | ||
==Emptying the chip collector== | ==Emptying the chip collector== | ||
[[Fil:Filter cleaning handle.jpg|miniatyr | [[Fil:Filter cleaning handle.jpg|miniatyr|Pull the black handle a few times to clean the filter.]] | ||
To empty the chip collector: | To empty the chip collector: | ||
*Before changing the bag, turn off the machine and pull | *Before changing the bag, turn off the machine and pull the black handle a few times to clean the filter. Wait a while to let the fine particles settle. | ||
*Pull the large handle upwards to lower the chip collector to the floor. | *Pull the large handle upwards to lower the chip collector to the floor. | ||
*Lift out the full bag and throw it in the garbage room. | *Lift out the full bag and throw it in the garbage room. (Take the keycard located in the cleaning closet outside the metalroom, and go to the garbage room which is the leftmost door on the truck loading dock out back. The door code is on the keycard.) | ||
*Take a new 200l bag from the | *Take a new 200l bag from the box on the ground next to the dust collector. | ||
*Roll in the collector and pull the handle down to lift it up and connect it. Make sure it is well aligned with the machine. | *Roll in the collector and pull the handle down to lift it up and connect it. Make sure it is well aligned with the machine. | ||
*Dispose of the full bag according to the instructions in [[Sophantering]] | |||
==Handhavande av maskinen== | ==Handhavande av maskinen== | ||
===Manual=== | ===Manual=== | ||
[https://www.yumpu.com/da/document/view/51465399/user-manual-dust-extractor-rl-125-rl-160-rl-200 Manual | [https://www.yumpu.com/da/document/view/51465399/user-manual-dust-extractor-rl-125-rl-160-rl-200 Manual for Felder RL] | ||
===Material=== | ===Material=== | ||
Only for wood! Metal chips may cause fires! | |||
==Underhåll och reservdelar== | ==Underhåll och reservdelar== | ||
===Underhåll=== | ===Underhåll=== | ||
| Rad 69: | Rad 64: | ||
**Check whether the seal between dust collector and unit is broken, replace if needed | **Check whether the seal between dust collector and unit is broken, replace if needed | ||
*TODO | *TODO | ||
** | **Automation of the dust collection system | ||
===Reservdelar=== | ===Reservdelar=== | ||
We do not have spare parts. Contact Felder directly to order more bags or a new filter. | We do not have spare parts. Contact Felder directly to order more bags or a new filter. | ||
We do have spare parts for the sprinkler heads. They should be in the locked maintenance drawer. | |||
==Logg== | ==Logg== | ||
*2025-11-06: Sprinkler system added | |||
*2020-02-XX: Sound absorber added | *2020-02-XX: Sound absorber added | ||
*2019-12-XX: Inköpt | *2019-12-XX: Inköpt | ||
==Länkar== | ==Länkar== | ||
https://www.felder-group.com/en-au/products/dust-extractors-extraction-units-c1963/clean-air-dust-extractor-performance-line-p144306 | https://www.felder-group.com/en-au/products/dust-extractors-extraction-units-c1963/clean-air-dust-extractor-performance-line-p144306 | ||
[[Fil:User Manual Dust Extractor RL 125 RL 160 RL 200.pdf]] | |||
==Ägare== | ==Ägare== | ||
| Rad 91: | Rad 87: | ||
==Gallery== | ==Gallery== | ||
<gallery> | <gallery> | ||
Fil:Felder 1.jpg|Switch knob and handle for cleaning the filter | Fil:Felder 1.jpg|Switch knob and handle for cleaning the filter. (Old woodroom) | ||
Fil:Felder 2.jpg|Do not cover the hole when replacing the bag | Fil:Felder 2.jpg|(Dated) Do not cover the hole when replacing the bag. (The hole exists to prevent the bag being sucked up into the filter. The hole allows a low pressure beneath the bag to keep it sucked down. This was replaced with a hose connected to the back.) | ||
Fil:Felder 4.jpg|Dust collection for the bandsaw | Fil:Felder 4.jpg|Dust collection for the bandsaw. (Old woodroom) | ||
Fil:Felder 3.jpg|Floor swiping | Fil:Felder 3.jpg|Floor swiping. (Old woodroom) | ||
Fil:Felder 5.jpg|Connection to table saw and table router | Fil:Felder 5.jpg|Connection to table saw and table router. (Old woodroom) | ||
Fil:Felder 6.jpg|Dust collection for the miter saw | Fil:Felder 6.jpg|Dust collection for the miter saw. (Old woodroom) | ||
</gallery> | </gallery> | ||
[[Kategori:Trärummet]] | |||
Nuvarande version från 6 november 2025 kl. 22.43
General information
The Felder RL 125 is a powerfull chip extractor connected to most of the machines in the woodshop. A sound absorber was added on top of the machine to keep the noise level acceptable. A combination of 100mm fixed pipes and flexible hoses with doors are used to direct the suction to the desired machine.
To use the vacuum, start the machine by turning the red knob and open the desired door connecting to the machine you are using. Check before starting that all the other doors are closed in order to get the most flow.
The vacuum should be used at anytime with the following machines:
- Table saw (dedicated hose)
- Table router and planer/jointer use the same hose. You can use it to clean around them as well.
- Band saw (dedicated hose)
- Miter saw (dedicated hose)
- Beltsander (dedicated hose)
- Lathe (one dedicated hose with large funnel)
It is not required to use the dust collection on the drill press.
Regularly check for the level of dust in the bag, and properly replace the plastic bag if needed. See instructions below.
Safety information
Things to consider when using the machine to not hurt the machine, others, and yourself.
Not much risks of injuring yourself, but a few things to keep in mind to keep the machine running safely:
- Do not cut or sand any wet wood as you could clog the filter (which is an expensive spare part)
- Check the level of dust in the bag and change the bag when reaching the maximum level.
- On the left side of the machine, there is a handle that you can pull a few times to clean the filter, do not perform this when the machine is running.
- Do not obstruct the air output.
Emptying the chip collector
To empty the chip collector:
- Before changing the bag, turn off the machine and pull the black handle a few times to clean the filter. Wait a while to let the fine particles settle.
- Pull the large handle upwards to lower the chip collector to the floor.
- Lift out the full bag and throw it in the garbage room. (Take the keycard located in the cleaning closet outside the metalroom, and go to the garbage room which is the leftmost door on the truck loading dock out back. The door code is on the keycard.)
- Take a new 200l bag from the box on the ground next to the dust collector.
- Roll in the collector and pull the handle down to lift it up and connect it. Make sure it is well aligned with the machine.
- Dispose of the full bag according to the instructions in Sophantering
Handhavande av maskinen
Manual
Material
Only for wood! Metal chips may cause fires!
Underhåll och reservdelar
Underhåll
- Daily
- Visual check whether unit or parts are damaged
- Check whether power cable is damaged
- Check whether dust bags are inserted and check if not full
- Weekly
- Machine powered off, pull the filter cleaning handle 4-5 times. This has to be done before every bag replacement.
- Monthly
- Visual check for leaks around the filter (dust ejected from the unit cover)
- Check whether the minimum exhaust volume control is functioning correctly
- Annually
- Visual check whether dust has collected in fan housing, remove if necessary
- Check whether the seal between dust collector and unit is broken, replace if needed
- TODO
- Automation of the dust collection system
Reservdelar
We do not have spare parts. Contact Felder directly to order more bags or a new filter.
We do have spare parts for the sprinkler heads. They should be in the locked maintenance drawer.
Logg
- 2025-11-06: Sprinkler system added
- 2020-02-XX: Sound absorber added
- 2019-12-XX: Inköpt
Länkar
Ägare
Maskinen inköpt av Makerspace 2019-12-XX
Gallery
-
Switch knob and handle for cleaning the filter. (Old woodroom)
-
(Dated) Do not cover the hole when replacing the bag. (The hole exists to prevent the bag being sucked up into the filter. The hole allows a low pressure beneath the bag to keep it sucked down. This was replaced with a hose connected to the back.)
-
Dust collection for the bandsaw. (Old woodroom)
-
Floor swiping. (Old woodroom)
-
Connection to table saw and table router. (Old woodroom)
-
Dust collection for the miter saw. (Old woodroom)
