Spånsug, Felder RL 125: Skillnad mellan sidversioner
(Clarified the instructions for emptying the collector) |
(Clarified what the filter cleaning handle is.) |
||
| Rad 14: | Rad 14: | ||
Near the belt sander, a pipe goes all the way to the floor and make the floor cleaning really easy. <br /> | Near the belt sander, a pipe goes all the way to the floor and make the floor cleaning really easy. <br /> | ||
Regularly check for the level of dust in the bag, and properly replace the plastic bag if needed | Regularly check for the level of dust in the bag, and properly replace the plastic bag if needed. See instructions below. | ||
==Säkerhetsinformation== | ==Säkerhetsinformation== | ||
''Saker man bör tänka på när man använder maskinen för att inte skada sig, andra, eller maskinen'' | ''Saker man bör tänka på när man använder maskinen för att inte skada sig, andra, eller maskinen'' | ||
| Rad 25: | Rad 25: | ||
*Do not obstruct the air output. | *Do not obstruct the air output. | ||
== Emptying the chip collector == | ==Emptying the chip collector== | ||
To empty the chip colector: | [[Fil:Filter cleaning handle.jpg|miniatyr]] | ||
To empty the chip colector: | |||
* Before changing the bag, turn off the machine and pull 4-5 time of the filter cleaning handle. | *Before changing the bag, turn off the machine and pull 4-5 time of the filter cleaning handle. The Filter cleaning handle is the black handle on the side of the machine, under the power connector. See the picture to the right. | ||
* Pull the large handle upwards to lower the chip collector to the floor. | *Pull the large handle upwards to lower the chip collector to the floor. | ||
* Lift out the full bag and trhow it in the garbage room. | *Lift out the full bag and trhow it in the garbage room. | ||
* Take a new 200l bag from the shelf above the wood lathe. | *Take a new 200l bag from the shelf above the wood lathe. | ||
* Roll in the collector and pull the handle down to lift it up and connect it. Make sure it is well aligned with the machine. | *Roll in the collector and pull the handle down to lift it up and connect it. Make sure it is well aligned with the machine. | ||
<br /> | |||
==Handhavande av maskinen== | ==Handhavande av maskinen== | ||
Versionen från 24 juni 2020 kl. 20.18
Generell information
The Felder RL 125 is a powerfull chip extractor connected to most of the machines in the woodshop. A sound absorber was added on top of the machine to keep the noise level acceptable. A combination of 100mm fixed pipes and flexible hoses with doors are used to direct the suction to the desired machine.
To use the vacuum, start the machine by turning the red knob and open the desired door connecting to the machine you are using. Check before starting it that all the other doors are closed in order to get the most flow. In a near futur, the vacuum will turn ON and OFF automatically when opening/closing the doors.
The vacuum should be used at anytime with the following machines:
- Table saw, table router and planer with the flexible hose. Use as well to clean around the miter saw and the lathe.
- Band saw (one dedicated flexible hose)
- Miter saw (two dedicated pipes)
In a near futur, the belt sander and drill press will have a dedicated hose too.
Near the belt sander, a pipe goes all the way to the floor and make the floor cleaning really easy.
Regularly check for the level of dust in the bag, and properly replace the plastic bag if needed. See instructions below.
Säkerhetsinformation
Saker man bör tänka på när man använder maskinen för att inte skada sig, andra, eller maskinen
Not much risks of injuring yourself, but a few things to keep in mind to keep the machine running safely:
- Do not cut or sand any wet wood as you could clog the filter (which is an expensive spare part)
- Check the level of dust in the bag and change the bag when reaching the maximum level.
- On the side of the machine, there is a handle that you can pull a few times to clean the filter, do not perform this when the machine is running.
- Do not obstruct the air output.
Emptying the chip collector
To empty the chip colector:
- Before changing the bag, turn off the machine and pull 4-5 time of the filter cleaning handle. The Filter cleaning handle is the black handle on the side of the machine, under the power connector. See the picture to the right.
- Pull the large handle upwards to lower the chip collector to the floor.
- Lift out the full bag and trhow it in the garbage room.
- Take a new 200l bag from the shelf above the wood lathe.
- Roll in the collector and pull the handle down to lift it up and connect it. Make sure it is well aligned with the machine.
Handhavande av maskinen
Manual
Material
Endast för trä!
Användarinstruktioner
Se till att koppla in dammsugare innan du använder den!
Underhåll och reservdelar
Underhåll
- Daily
- Visual check whether unit or parts are damaged
- Check whether power cable is damaged
- Check whether dust bags are inserted and check if not full
- Weekly
- Machine powered off, pull the filter cleaning handle 4-5 times. This has to be done before every bag replacement.
- Monthly
- Visual check for leaks around the filter (dust ejected from the unit cover)
- Check whether the minimum exhaust volume control is functioning correctly
- Annually
- Visual check whether dust has collected in fan housing, remove if necessary
- Check whether the seal between dust collector and unit is broken, replace if needed
- TODO
- Add a door and a double connection to the belt sander and the drill press
- Automatisation of the dust collection system
- 24V relay + tempo
Reservdelar
We do not have spare parts. Contact Felder directly to order more bags or a new filter.
Logg
- 2020-02-XX: Sound absorber added
- 2019-12-XX: Inköpt
Länkar
Ägare
Maskinen inköpt av Makerspace 2019-12-XX
Gallery
-
Switch knob and handle for cleaning the filter
-
Do not cover the hole when replacing the bag
-
Dust collection for the bandsaw
-
Floor swiping
-
Connection to table saw and table router
-
Dust collection for the miter saw
