Plan- och rikthyvel, Scheppach HMC 3200: Skillnad mellan sidversioner

VisuellWikitext

Versionen från 17 februari 2022 kl. 15.10

Snabbfakta Scheppach EMC 3200

Modell: Scheppach HMC 3200

Bokningsbar: Nej

Kostnad att använda: Gratis

Max board width: 32 cm

Max board height: 18 cm

Generell information

The use of pallet wood, reclaimed flooring, reclaimed outdoor deck planks and any king of wood used for concrete formwork is totally forbidden.

Before jointing or planing, the boards should be inspected for nails, screws or any metallic chips.

Wood planks must be cleaned with a hard brush to remove sand dust.

Säkerhetsinformation

Wear safety glasses, keep hands at least 15 cm from the cutterhead
Make adjustments with the machine powered off
Check planer table before turning it on, a tool might have slipped under the cutter head
Stock must be at least 30 cm long. Minimum 6 mm thick for jointer, 4 mm for planning
Blades must be sharp. Dull blades will vibrate the stock and may cause a kickback.
Clean tool and work area when done
Feed the work so that the knives will cut “with the grain”. Use only stock that is free of knots and splits. Do not plane end grain
Use a push block when planing a flat surface. Never apply pressure directly over the knives with your hand.
Do not plane the maximum amount off of stock when planing. Two passes through the planer can be better than one.
When planning thin pieces of wood, be sure to stand to one side in case the wood breaks and kicks back.
Support the work properly at the in feed and at the out feed.

Handhavande av maskinen

Manual

Sprängskiss: Fil:Scheppach hmc 3200 planing combi.pdf

Material

Endast för trä! Do to use wet or green wood. Wait 24 hours before planing glued wood pieces or pieces with epoxy.

Use only clean (without nails, screws or sand particles) wood. No other material allowed.

The use of pallet wood, reclaimed flooring, reclaimed outdoor deck planks and any king of wood used for concrete formwork is totally forbidden.

Användarinstruktioner

Se till att koppla in dammsugare innan du använder den!

Förbrukningsmaterial

The new spiral cutterhead uses 15mmx15mmx2.5mm-R150 carbide inserts. We have a set of 10 spare.

The inserts can be rotated 3 times before being replaced. The recommended torque range is 5.4-5.9 Nm (48-52 pound inch).

~~We currently have 3 sets of blades. Label and store the dull blades. When two sets are dull, send them to resharpening.~~

Underhåll och reservdelar

Underhåll

Daily
- Visual check whether unit or parts are damaged
- Check whether power cable is damaged
- Check if there is any parts loose around the blades before plugging and running it.

Monthly
- Check the blade sharpness. Change blade if necessary.
Annually
- Remove the front cover to clean and grease the transmission chain and clean the clutch plates

Reservdelar

Small yellow belt for the feed mechanism. One spare.

1012 needle bearings for the feed mechanism. 2 spare.

Logg

2022-02-16: installed the new spiral cutterhead with new bearings.
2021-06-01: replaced two needle bearings on the plastic gear in the autofeed mechanism.
2021-01-xx: new motor and new motor protection. Some gears of the autofeed mechanism replaced.
2020-11-01: motor keyway and pulley damaged. Machine under maintenance
2020-03-19: Fence installed
2020-01-XX: dust collector built for the planer
20XX: Inköpt

@@ Rad 19: / Rad 19: @@
 ==Generell information==
-<br />
+'''<big>The use of pallet wood, reclaimed flooring, reclaimed outdoor deck planks and any king of wood used for concrete formwork is totally forbidden.</big>'''
+Before jointing or planing, the boards should be inspected for nails, screws or any metallic chips.
+Wood planks must be cleaned with a hard brush to remove sand dust. <br />
 ==Säkerhetsinformation==
@@ Rad 43: / Rad 47: @@
 Use only clean (without nails, screws or sand particles) wood. No other material allowed.
+'''<big>The use of pallet wood, reclaimed flooring, reclaimed outdoor deck planks and any king of wood used for concrete formwork is totally forbidden.</big>'''
 ===Användarinstruktioner===
 Se till att koppla in dammsugare innan du använder den!
 ==Förbrukningsmaterial==
-We currently have 3 sets of blades. Label and store the dull blades. When two sets are dull, send them to resharpening.
+The new spiral cutterhead uses 15mmx15mmx2.5mm-R150 carbide inserts. We have a set of 10 spare.
+The inserts can be rotated 3 times before being replaced. The recommended torque range is 5.4-5.9 Nm (48-52 pound inch).
+<s>We currently have 3 sets of blades. Label and store the dull blades. When two sets are dull, send them to resharpening.</s>
 ==Underhåll och reservdelar==
@@ Rad 72: / Rad 82: @@
 ==Logg==
+*2022-02-16: installed the new spiral cutterhead with new bearings.
 *2021-06-01: replaced two needle bearings on the plastic gear in the autofeed mechanism.
 *2021-01-xx: new motor and new motor protection. Some gears of the autofeed mechanism replaced.