Plan- och rikthyvel, Scheppach HMC 3200: Skillnad mellan sidversioner

Från Stockholm Makerspace Wiki
m (SamanFanni flyttade sidan Plan- och rikthyvel, Scheppach EMC 3200 till Plan- och rikthyvel, Scheppach HMC 3200: Felskrivet modellnamn. från "EMC" till "HMC".)
Ingen redigeringssammanfattning
Rad 110: Rad 110:


[[Kategori:Trärummet]]
[[Kategori:Trärummet]]
[[Kategori:Trä]]

Versionen från 25 april 2023 kl. 20.35

Snabbfakta Scheppach HMC 3200
Modell: Scheppach HMC 3200
Bokningsbar: Nej
Kostnad att använda: Gratis
Max board width: 32 cm
Max board height: 18 cm


Generell information

The use of pallet wood, reclaimed flooring, reclaimed outdoor deck planks and any kind of wood used for concrete formwork is totally forbidden.

Before jointing or planing, the boards should be inspected for nails, screws or any metallic chips.

Wood planks must be cleaned with a hard brush to remove sand dust.

Safety instructions

  • Wear safety glasses, keep hands at least 15 cm from the cutterhead
  • Make adjustments with the machine powered off
  • Check planer table before turning it on, a tool might have slipped under the cutter head
  • Stock must be at least 30 cm long. Minimum 6 mm thick for jointer, 4 mm for planning
  • Blades must be sharp. Dull blades will vibrate the stock and may cause a kickback.
  • Clean tool and work area when done
  • Feed the work so that the knives will cut “with the grain”. Use only stock that is free of knots and splits. Do not plane end grain
  • Use a push block when planing a flat surface. Never apply pressure directly over the knives with your hand.
  • Do not plane the maximum amount off of stock when planing. Two passes through the planer can be better than one.
  • When planning thin pieces of wood, be sure to stand to one side in case the wood breaks and kicks back.
  • Support the work properly at the in feed and at the out feed.

Handhavande av maskinen

Manual

Sprängskiss: Fil:Scheppach hmc 3200 planing combi.pdf

Material

Endast för trä! Do to use wet or green wood. Wait 24 hours before planing glued wood pieces or pieces with epoxy.

Use only clean (without nails, screws or sand particles) wood. No other material allowed.

The use of pallet wood, reclaimed flooring, reclaimed outdoor deck planks and any kind of wood used for concrete formwork is totally forbidden.

Dust collection instructions when planing

Mount the yellow dust collector attachment when using it as a planer, and make sure it is connected to the central vacuum.

Dust collection instructions when jointing

Use the dust collector attachment that looks like a brown box. Set the table to 10.5-11 cm, enough for the box to fit and to still be able to adjust the in-feed table height. The box stays in place with some magnets. Connect the box to the central vacuum.

Spiral cutterhead

The new spiral cutterhead uses 15mmx15mmx2.5mm-R150 carbide inserts. We have a set of 10 spare.

The inserts can be rotated 3 times before being replaced. The recommended torque range is 5.4-5.9 Nm (48-52 pound inch).

We currently have 3 sets of blades. Label and store the dull blades. When two sets are dull, send them to resharpening.

Underhåll och reservdelar

Underhåll

  • Daily
    • Visual check whether unit or parts are damaged
    • Check whether power cable is damaged
    • Check if there is any parts loose around the blades before plugging and running it.
  • Monthly
    • Check the blade sharpness. Change blade if necessary.
  • Annually
    • Remove the front cover to clean and grease the transmission chain and clean the clutch plates

Reservdelar

Small yellow belt for the feed mechanism. One spare.

1012 needle bearings for the feed mechanism. 2 spare.

Logg

  • 2022-02-16: installed the new spiral cutterhead with new bearings.
  • 2021-06-01: replaced two needle bearings on the plastic gear in the autofeed mechanism.
  • 2021-01-xx: new motor and new motor protection. Some gears of the autofeed mechanism replaced.
  • 2020-11-01: motor keyway and pulley damaged. Machine under maintenance
  • 2020-03-19: Fence installed
  • 2020-01-XX: dust collector built for the planer
  • 20XX: Inköpt

Länkar

Wood Jointer Tips for Setting Up and Using a Jointer - WoodWorkWeb

Ägare

Maskinen inköpt av Makerspace

Gallery