Bandsåg, EJCA BA45

Från Stockholm Makerspace Wiki
Version från den 10 september 2024 kl. 18.24 av Voxel (diskussion | bidrag)
(skillnad) ← Äldre version | Nuvarande version (skillnad) | Nyare version → (skillnad)
Snabbfakta EJCA BA45
Modell: EJCA BA45
Bokningsbar: Nej
Kostnad att använda: Gratis
Obelastad hastighet: -
Blade length: 3090 mm
Wheels-Ø: 446 x 32 mm
Märkeffekt: 1.0 hk


Generell information

Bandsåg för trä

Gedigen gjutjärnsmaskin tillverkad på 60- till 70-talet.

OBS! Kräver genomgång av kurs före användning! / Requires completion of course before use!


/// VERY IMPORTANT INFORMATION ///

This machine has a wide blade installed. This means it is only for straight cuts (or very wide curves). Use the other bandsaw for curves.

Säkerhetsinformation

  • Wheel guard doors closed and blade properly adjusted before turning on the machine
  • Upper guide assembly no more than 1cm above the work
  • Allow the saw to reach full speed before starting to feed the work
  • The stock must be held flat on the table
  • Feed the saw only as fast as the teeth will remove the wood easily
  • Keep hands at least 10 cm away from the blade
  • Plan cuts to avoid backing out of curves, whenever possible
  • Make turns carefully and do not cut radii so small that the blade is twisted then broken
  • Round stock should not be cut unless mounted firmly in a jig
  • Do not let small pieces of wood accumulate around the blade
  • If you hear a clicking noise, turn off the machine at once. This sound indicates a crack in the blade
  • Turn off the machine as soon as you finish working
  • Sweep the table and the floor. All scrap in the scrap bin. Lower the upper guide assembly

Handhavande av maskinen

Manual

Instruktionsbok_Ejca_BA40,45,50

Material

Endast för trä! Do not cut wet or green wood. Do not cut freshly glued wood, wait at least 24h before cutting.

Some plastics and foam can be cut using this saw.

Användarinstruktioner

Se till att koppla in dammsugare innan du använder den!

Skriv något om hur man ställer de olika vinklarna

Byta blad på bandsågen

Det är viktigt att du ställer in spänningen på bladet rätt och att guiderna för bladet också är rätt inställda. Här är en bra video som går igenom hur du gör det: https://www.youtube.com/watch?v=bxVyKsbuwZQ.

English: Changing the blade on the bandsaw

It is very important that you adjust the belt tension and the blade guides correctly. Here is a great video that explains exactly how to do this: https://www.youtube.com/watch?v=bxVyKsbuwZQ.

Förbrukningsmaterial

The blades provided by the makerspace, for this saw, are for resawing.

Blade length: 3090 mm

3086mm / 19mm / 4TPI


To order new blades: http://www.bandsagblad.se/

Underhåll och reservdelar

Underhåll

  • Daily
    • Check for the blade alignment, and blade guide alignment (upper and lower guides).
    • Adjust the upper blade guide assembly height
    • Visual check whether unit or parts are damaged
    • Check whether power cable is damaged
    • Vacuum and clean the saw.
  • Monthly
    • Check the blade sharpness. Change blade if necessary.
    • Check the lower blade garde wooden blocs and replace them is necessary.
    • Check and clean the inside of the saw and inspect the tires
  • Annually
    • Grease the lower and upper wheel shafts. After letting the saw run for a few minutes, wipe out the excess of grease.
  • TODO
    • Balance the wheels

Reservdelar

We have the set of spare bearings for the top and the bottom wheels. If they ever need to be replaced.

/// Add link for the new tires ///

Logg

  • 2024-05-XX: Changed to permanently have a wide blade mounted. We now have a different table saw for curves.
  • 2020-03-XX: New urethane tires and upper blade guides
  • 2020-02-XX: 100mm vacuum connector added
  • 2018-XX-XX: Har fått motorskydd, nödstopp samt nya start och stoppknappar
  • 2018-XX-XX: Inköpt

Länkar

Bandsaw Tips and Tricks for Woodworkers - Make Something

The Best Way to Set Up a Bandsaw

Ägare

Maskinen inköpt av Makerspace 2018-XX-XX

Gallery