166
redigeringar
Plan- och rikthyvel, Scheppach HMC 3200: Skillnad mellan sidversioner
Plan- och rikthyvel, Scheppach HMC 3200 (visa wikitext)
Versionen från 25 februari 2020 kl. 23.18
, 25 februari 2020ingen redigeringssammanfattning
mIngen redigeringssammanfattning |
Cloraux (diskussion | bidrag) Ingen redigeringssammanfattning |
||
| Rad 1: | Rad 1: | ||
{| style="clear: right; float: right; width: 20em; padding: 0.3em; margin: 0.5em 0 0.5em 1em; border: 1px solid #A3B1BF; background: #f5faff; text-align: left; font-size: 100%; line-height: 1.5em;" | |||
|- | |||
| align="center" |'''Snabbfakta Bosch GCM8 SJL''' | |||
|- | |||
|[[Fil:Scheppach_hmc_3200.jpg|200px|center]] | |||
|- | |||
| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Modell:''' ''Scheppach HMC 3200'' | |||
|- | |||
| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Bokningsbar:''' Nej | |||
|- | |||
| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Kostnad att använda:''' Gratis | |||
|- |- | |||
| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Info 1:''' Kap- och gersåg | |||
|- | |||
| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Arbetsyta:''' 32 cm | |||
|- | |||
| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Obelastad hastighet:''' - RPM | |||
|- | |||
| style="padding:0.1em; font-size:1.0em; background-color:#dfeff2" |'''Märkeffekt:''' - W | |||
|- | |||
|}<br /> | |||
==Generell information== | |||
Sågen kan vinklas 52° Vänster till 60° Höger i förhållande till anhållet i bakkant (geringsvinkel) | |||
Sågen kan vinklas 47° Vänster till 2° Höger i förhållande till bordet (snedkapningsvinkel) | |||
This saw can be used to cut relatively large pieces of wood and is ideal to make cross-cuts. It is set for square, miter and bevel cuts, or a combination of miter and bevel cuts (compound cut). | |||
The saw is attached to the table with 4 screws and some angle combinations are unavailable due to the present configuration. | |||
It is possible to unscrew the saw and move it to perform special cuts or to cut longer pieces. The saw must be set back to it's initial position. | |||
This saw can be use to perform non-through cuts (Dados, Grooves & Rabbets) using the depth stop. For such operation, it's usually required to install a sacrificial fence (see pictures in the galerie) | |||
==Säkerhetsinformation== | |||
*Wear safety glasses, keep hands at least 15 cm from the cutterhead | |||
*Make adjustments with the machine powered off | |||
*Check planer table before turning it on, a tool might have slipped under the cutter head | |||
*Stock must be at least 30 cm long. Minimum 6 mm thick for jointer, 4 mm for planning | |||
*Blades must be sharp. Dull blades will vibrate the stock and may cause a kickback. | |||
*Clean tool and work area when done | |||
*Feed the work so that the knives will cut “with the grain”. Use only stock that is free of knots and splits. Do not plane end grain | |||
*Use a push block when planing a flat surface. Never apply pressure directly over the knives with your hand. | |||
*Do not plane the maximum amount off of stock when planing. Two passes through the planer can be better than one. | |||
*When planning thin pieces of wood, be sure to stand to one side in case the wood breaks and kicks back. | |||
*Support the work properly at the in feed and at the out feed. | |||
==Handhavande av maskinen== | |||
===Manual=== | |||
[https://www.bosch-professional.com/binary/ocsmedia/optimized/full/o290859v21_160992A4D3_201808.pdf Manual på Boschs hemsida] | |||
===Material=== | |||
Endast för trä! | |||
Some plastics can be cut using this saw, but you need to use your own dedicated blade. Always disconnect the power before changing the blade and make sure it's properly centered before starting the saw. | |||
===Användarinstruktioner=== | |||
Se till att koppla in dammsugare innan du använder den! | |||
'''''Skriv något om hur man ställer de olika vinklarna''''' | |||
==Förbrukningsmaterial== | |||
We currently have XX spare blades for the miter saw. These blade can be resharpened, do not throw them away, instead label them as "DULL". | |||
The blades provided by the makerspace are for general purpose and designed for cross-cutting and have about XX teeth. | |||
You can buy and install your own blade for some specific projects (cutting plastics, Flat kerf blades for joinery, etc) but you must install back the original blade when you are done. | |||
Klingdiameter: 216 mm | |||
Klinghåls-Ø: 30 mm | |||
==Underhåll och reservdelar== | |||
===Underhåll=== | |||
*Daily | |||
**Visual check whether unit or parts are damaged | |||
**Check whether power cable is damaged | |||
**Vacuum and clean the saw and the dust collection box. Throw away scrap wood. | |||
*Monthly | |||
**Check the blade sharpness. Change blade if necessary. | |||
**Clean the laser plastic cover and remove gunk and dust on the saw. | |||
===Reservdelar=== | |||
We do not have spare parts for this machine. | |||
# | |||
==Logg== | |||
*2020-02-XX: Miter saw station build next to the dust collector. | |||
*2019-10-05: Inköpt | |||
* | |||
==Länkar== | |||
https://www.bosch-professional.com/se/sv/products/gcm-8-sjl-0601B19100 | |||
[https://www.youtube.com/watch?v=1HI_1bj4J1U 8 Miter Saw Pro Tips & Tricks - Steve Ramsey - Woodworking for Mere Mortals] | |||
==Ägare== | |||
Maskinen inköpt av Makerspace | |||
==Gallery== | |||
<gallery> | |||
Fil:MiterSaw.jpg|Cross-cutting large solid planks | |||
</gallery> | |||
[[Fil:Scheppach_hmc_3200.jpg|400px|thumb|left|Scheppach HMC 3200]] | [[Fil:Scheppach_hmc_3200.jpg|400px|thumb|left|Scheppach HMC 3200]] | ||
| Rad 8: | Rad 126: | ||
Sprängskiss: [[Fil:Scheppach_hmc_3200_planing_combi.pdf]] | Sprängskiss: [[Fil:Scheppach_hmc_3200_planing_combi.pdf]] | ||