166
redigeringar
Spånsug, Felder RL 125: Skillnad mellan sidversioner
→Generell information
Ingen redigeringssammanfattning |
Cloraux (diskussion | bidrag) |
||
| Rad 2: | Rad 2: | ||
[[Fil:Felder RL 125.jpg|miniatyr]]The [https://www.felder-group.com/en-us/products/dust-extractors-c1963 Felder] RL 125 is a powerfull chip extractor connected to most of the machines in the woodshop. A sound absorber was added on top of the machine to keep the noise level acceptable. A combination of 100mm fixed pipes and flexible hoses with doors are used to direct the suction to the desired machine. | [[Fil:Felder RL 125.jpg|miniatyr]]The [https://www.felder-group.com/en-us/products/dust-extractors-c1963 Felder] RL 125 is a powerfull chip extractor connected to most of the machines in the woodshop. A sound absorber was added on top of the machine to keep the noise level acceptable. A combination of 100mm fixed pipes and flexible hoses with doors are used to direct the suction to the desired machine. | ||
To use the vacuum, start the machine by turning the red knob and open the desired door connecting to the machine you are using. Check before starting it that all the other doors are closed in order to get the most flow. In a near | To use the vacuum, start the machine by turning the red knob and open the desired door connecting to the machine you are using. Check before starting it that all the other doors are closed in order to get the most flow. In a near future, the vacuum will turn ON and OFF automatically when opening/closing the doors. | ||
The vacuum should be used at anytime with the following machines: | The vacuum should be used at anytime with the following machines: | ||
| Rad 8: | Rad 8: | ||
*Table saw, table router and planer with the flexible hose. Use as well to clean around the miter saw and the lathe. | *Table saw, table router and planer with the flexible hose. Use as well to clean around the miter saw and the lathe. | ||
*Band saw (one dedicated flexible hose) | *Band saw (one dedicated flexible hose) | ||
*Miter saw (two dedicated pipes) | *Miter saw (two dedicated pipes on the enclosure) | ||
*Beltsander (one dedicated flexible hose) | *Beltsander (one dedicated flexible hose) | ||
*Lathe (one dedicated hose with large funnel - under construction) | |||
It is not required to use the dust collection on the drill press, however it is useful when drilling large holes. | It is not required to use the dust collection on the drill press, however it is useful when drilling large holes. | ||
Regularly check for the level of dust in the bag, and properly replace the plastic bag if needed. See instructions below. | Regularly check for the level of dust in the bag, and properly replace the plastic bag if needed. See instructions below. | ||
| Rad 32: | Rad 32: | ||
To empty the chip collector: | To empty the chip collector: | ||
*Before changing the bag, turn off the machine and pull 4-5 time of the filter cleaning handle. The Filter cleaning handle is the black handle on the side of the machine | *Before changing the bag, turn off the machine and pull 4-5 time of the filter cleaning handle. The Filter cleaning handle is the black handle on the side of the machine on the lathe side. See the upper picture to the right. | ||
*Pull the large handle upwards to lower the chip collector to the floor. | *Pull the large handle upwards to lower the chip collector to the floor. | ||
*Lift out the full bag and | *Lift out the full bag and throw it in the garbage room. | ||
*Take a new 200l bag from the shelf above the wood lathe. | *Take a new 200l bag from the shelf above the wood lathe. | ||
*Do not cover the hole in the corner when replacing the bag. See the lower picture to the right. | *Do not cover the hole in the corner when replacing the bag. See the lower picture to the right. | ||
| Rad 69: | Rad 69: | ||
**Check whether the seal between dust collector and unit is broken, replace if needed | **Check whether the seal between dust collector and unit is broken, replace if needed | ||
*TODO | *TODO | ||
**Automatisation of the dust collection system | **Automatisation of the dust collection system | ||
===Reservdelar=== | ===Reservdelar=== | ||